GILES FSH-4 Hood Скачать руководство пользователя страница 51

Страница: 51 / 68

Model: FSH-4 Hood

Hood Cleaning & Maintenance

To maintain effectiveness and performance, the Hood must be deep cleaned, at a minimum, every 3 months.
1. Disconnect power from the unit at circuit breaker.
2. If possible, unplug and remove appliances from underneath hood.
3. Remove all of the filters.
4. Use a soft cloth, or sponge, and a mild bio-degradable decreasing cleaner

(Simple Green® Crystal Foaming

Spray Degreaser/Cleaner is recommended)

to clean the entire hood plenum, removing grease film

accumulation from interior surfaces.

5. Inspect the hood blowers on each side and, if possible, clean grease build-up from the blades using degreaser

and a small brush (use cleaner sparingly).

NOTE: When restarting Hood after cleaning, hold a cardboard box,

or other suitable item, over the exhaust outlet to catch cleaning residue which may be discharged from the

blowers

5. Thoroughly clean the under-hood area and all exterior surfaces with mild degreaser or a good quality stainless

steel cleaner.

6. Allow hood to thoroughly dry or wipe dry with clean dry cloth.
7. Clean baffle filters and E.A.C. collector cells see

Sections 4.04.1 & 4.04.2.

If necessary, obtain and install a new

fresh pre-filters and charcoal filters

Ensure all filters are reinstalled in the hood.

8. As necessary, reposition appliance under hood and restore power supply to the hood.

5.02

Quarterly Hood Cleaning

The factory-recommended product to use for general cleaning/degreasing of this equipment is

Simple Green®

Crystal Foaming Spray Degreaser/Cleaner

, a readily available, biodegradable, non-toxic degreasing cleaner

The fire extinguishing system connected to the Hood must be maintained in accordance with the

Standard for Wet

Chemical Extinguishing Systems, NFPA 17A

and with the instructions of the system’s installer.

All inspection, maintenance, troubleshooting, repairs and general servicing of the fire extinguishing system must be

performed by an authorized

Ansul® Distributor/Dealer

. Required maintenance activities are explained in the

following sections.

Consult the Fire Suppression System documentation provided by the system installer for complete maintenance

guidelines.

5.03

Fire Suppression System Maintenance

DO NOT

wash down hood with water from a spray hose.

DO NOT

steam clean or use pressure washing equipment.

DO NOT

use products containing chlorine or other caustic chemicals.

DO NOT

use abrasive products, steel wool or scouring pads.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды