GILES FSH-4 Hood Скачать руководство пользователя страница 45

Страница: 45 / 68

Model: FSH-4 Hood

Operation & Filter Maintenance

Two L.E.D. indicator light clusters on the Control Panel show the operational status of the E.A.C. Filter system for

each side of the Hood.

4.03.3

E.A.C. Filter Status & Alarm

4.04

Filter Maintenance

[ON]

Indicates that the E.A.C. cell is installed, powered and operating. Only light

when the system is

operating normally.

[WASH]

This light turns

to indicate:

• Filter cell is not installed or is mis-aligned.

• Collection fins contain excessive amount of captured

grease residue.

• Poor contact with filter cell contact plate inside hood.

• Ionizer wire, or wires, completely missing.

When

[WASH]

light is

, an alarm condition exists and air

cleaning is not occurring. After approximately two (2)

minutes, an intermittent (beeping) alarm tone will begin sounding and shortly thereafter, power to the

appliances under the hood is shutdown and

[APPLIANCE POWERED]

light turns

OFF

[WASH}

light is

NOT

intented to be a signal for routine cleaning of the cell,

DO NOT use as such

Typically, the collection cell must be cleaned

DAILY

to ensure optimum performance. See

Section 4.04.2,

EAC Filter Cell Cleaning

[CHECK]

This light turns

to indicate:

• Ionizer wire broken and touching cell frame.

• Cell is damaged and has shorted out to ground.

• Collection fins are shorted out because of excessive moisture.

When

[CHECK]

light is

ON,

system is no longer operating to clean the air, even though the hood continues

to run and the appliances are powered.

DO NOT CONTINUE TO USE APPLIANCES WHEN THIS CONDITION

EXIST; DETERMINE THE CAUSE AND CORRECT!

The following actions may clear the alarm condition:
1. Turn

OFF

hood

Power Switch

2. Remove the E.A.C. cell and clean as described in

Section 4.04.2

3. Inspect the cell for broken or missing ionizer wires, bent fins, or other damage. Ionizer wires are replaceable

(when ordering replacements, note length ... available in

16” or 20”

). Bent fins may be gently straightened by

hand, such that no fins are touching adjacent fins. A cell with excessive damage (broken frame, badly bent

frame, broken insulators, etc) must be replaced.

4. Inspect the E.A.C. contact pad inside hood. Clean grease accumulation away with a mild degreasing cleaner and

dry thoroughly.

5. Replace filter cell

(

Section 4.02.7

)

and restart Hood

(Section 4.01)

. If the condition persist, contact a qualified

service technician. If none of the LED lights turn

, EAC power supply may be faulty.

The following sections describe procedures necessary for cleaning and maintaining filters in the

FSH-4 Ventless

Hood

. Conscientious adherence to these procedures is essential for maintaining optimum and satisfactory hood

performance.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды