CHAPTER 3: IEC 61850 COMMUNICATION
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
UR SERIES – COMMUNICATIONS GUIDE
3-131
3
EqLim
SPS
The number of pulses counted is equal to the set number
DigCntFCNT
EqpMismat
SPS
The configuration of modules does not match the stored order code
LPHD
EvtEna1
ENG
Setting to enable generation of events in event record, 0 = Disabled, 1 = Enabled
Rec3pRREC,
Rec13pRREC,
AuxOvPTOV,
AuxUvPTUV,
B_IocPIOC,
B_TocPTOC,
Bkr?XCBR,
BkrFaRBRF, GGIO3,
NegDocRDIR
EvtRcdClr
SPC
Clear Event Records (erase all Events), same action as command CLEAR EVENT
RECORDS?
Master/LLN0
FlexErrTkn
SPS
A FlexLogic equation is incorrect
LPHD
FltLinID
VSS
Faulted line ID
FltRFLO
FrstEthFail
SPS
First Ethernet failure
LPHD
Function1
ENG
Function Enable/Disable setting: 0 = Disabled, 1 = Enabled (note that TISSUE 670
suggests something like this named SetMod)
Rec3pRREC,
Rec13pRREC,
AuxOvPTOV,
AuxUvPTUV,
B_IocPIOC,
B_TocPTOC,
Bkr?XCBR, Master/
LLN0, GGIO2,
TrBusPTRC
FwdOp
SPS
Fault direction is forward
NegDocRDIR,
NeuDocRDIR
GoDatSetRef
ORG
Expected value of datSet field in messages subscribed to by RxGOOSE#
LGOS
GoEnaPort1
ENG
Enable all GOOSE on Ethernet port setting: 0 = Disabled, 1 = Enabled
Master/LLN0
GoID
VSG
Expected value of goID field in messages subscribed to by RxGOOSE#
LGOS
GpsFail1
SPS
GPS failed at terminal corresponding to instance number
LinDfPDIF
GrAct1
SPS
Setting group corresponding to index is active
Master/LLN0 (not in
C30)
HzChgRte
MV
Frequency rate of change measured value
RteHzPFRC
Id1
VSG
Name setting
ACsrcMMXU,
Bkr?XCBR,
FlxLgcGAPC, GGIO2
IdFail1
SPS
ID check for a peer L30/L90 on the channel has failed
LinDfPDIF
IndFailBeh
ENG
Setting to select the behavior of the RxGOOSE Boolean when the sending device is
offline: 0 = On, 1 = Off, 2 = Latest/On, 3 = Latest/Off
GGIO3
IndPos
DPS
Generic remote DPS input status values: 0 for intermediate-state, 1 for off, 2 for on, 3 for
bad-state
GGIO3
InitMod
ENG
Initiate mode setting: 0 = Protection and CB, 1 = Protection Only
Rec13pRREC
IntermSt1
SPS
Intermediate-status detected
Bkr?XCBR,
Disc?XSWI, GGIO3
IrigbFail
SPS
A bad IRIG-B input signal has been detected
LPHD
IsoBlk
ACT
B90 - Indicates that the isolator position is invalid
B_IsoSSWI
IsoPos
ACT
B90 - Indicates position of isolator. When "On", the related current is included in
differential zone; when "Off", the current is excluded from differential calculations.
B_IsoSSWI
LastSqNum
INS
Last sequence number received
LGOS
LatchErr
SPS
A difference is detected between the desired and actual latch contact state
LPHD
LeoSt
SPS
Line end open status
LinPkpPIOC
LivDea
SPS
This data object indicates that live/dead conditions have been met
SynChkRSYN
LivDeaDpo
SPS
This data object indicates that live/dead conditions have not been met
SynChkRSYN
Data object
name
CDC
Semantics
Used in logical
nodes…
Содержание UR series
