Full Spectrum Laser HL40-5g Hobby Advanced Скачать руководство пользователя | Manualshive

Страница: 23 / 91

background image

22

Assembly Stage Five: Connect Electrical Power

The Full Spectrum Hobby Advanced Laser System and available accessories are configured to
accept 110VAC at 60Hz. 220VAC units connect to power through an included converter
(singlephase 220VAC).

CONNECTING ELECTRICAL POWER STEPS:

1. Prepare Power Cord.

Remove the electrical cord (J) from its packaging.

2. Plug in Power Cord To Laser Cutter

. The power cord plugs into a “C14” power receptacle

located on the right side of the machine.

3. Plug in Power Cord to Outlet.

FInally, plug the power cord into any proper outlet socket in

your workspace.

PRO TIP! Please be aware that the accessories will increase the circuit
load; the most significant power draw usually comes from the
blower/exhaust system. Consult the manufacturer’s information and
manual for the operating parameters of your exhaust system.

POWER ON/OFF: the laser’s power is controlled by the large red button
(estop) located on the top of the case in the far right. This is an open
twist to release button. To power the laser down, simply press the button
down until it locks. To power the laser up, twist the button clockwise
according to the indicating arrows on the surface of the button.

IN CASE OF A BLOWN FUSE: determine the cause of the overload before
replacement to protect the machine from damage. The laser system is
equipped with a fuse on the power inlet to protect the machine from
surges or short circuits. The fuse is userchangeable (machine ships with
10A fuse installed). If problem persists, contact customer support.

CAUTION! do not replace the installed 10 amp fuse with a fuse of a higher
rating. This will void your warranty and the electronics will not be
adequately protected from surges or short circuits.

Technical Support is available from 8:00 am (PST) to 5:00 pm (PST) Monday through Friday at

[email protected]

.

«
...
21
22
23
24
25
...
»

Содержание HL40-5g Hobby Advanced




























































































Отзывы:

Нет отзывов

Похожие инструкции для HL40-5g Hobby Advanced

Бренд: Temper Страницы: 16

Бренд: VAIL PRODUCTS Страницы: 44

Бренд: Lervia Страницы: 14

Incredi-Pull 316.725860

Бренд: Craftsman Страницы: 72

Бренд: Sharp Страницы: 50

Бренд: Sharp Страницы: 88

Бренд: Mega Machine Страницы: 29

Бренд: YILMAZ Страницы: 21

Бренд: Stihl Страницы: 92

Бренд: Caiman Страницы: 28

Бренд: Zenoah Страницы: 20

Бренд: Zenoah Страницы: 64

Бренд: Zenoah Страницы: 68

Бренд: SANLI Страницы: 30

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 27

POWERPLUS POWEG8012

Бренд: VARO Страницы: 14

Бренд: DAISHIN Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды