Full Spectrum Laser HL40-5g Hobby Advanced Скачать руководство пользователя | Manualshive

Страница: 18 / 91

background image

17

With your laser cutter unboxed and placed in its permanent work space we can now assemble it.
This is a simple process that should take less than half an hour to complete. The following stages
will be described in detail.

Assembly Stages:

1. Remove the Zip Ties
2. Connect the Exhaust
3. Assemble the Water Pump
4. Assemble the Air Compressor (Recommended)
5. Connect Power
6. Connect the Ethernet Cable
7. Install RetinaEngrave Software

In addition, you will need the following tools and accessories (not included with your machine
purchase):

1. 35 gallons of distilled water
2. A five gallon bucket
3. Small scissors
4. Aluminum Tape
5. Ducting Tube
6. Exhaust Fan (recommended)
7. Internet connection (to download software)

Assembly Stage One: Remove Zip Ties

To secure the machine during shipping, zip ties are used to hold the X belt, the Y belts and the
laser head. These must be removed before operating your laser cutter for the first time.

REMOVE ZIP TIE STEPS:

1. Locate Zip Ties.

There are a total of four (4) zip ties that need to be cut and removed. One

is located on the laser head, one is located on the X belt and the last two are located on the
left and right Y belts.

2. Cut and Remove Four (4) Zip Ties.

Using a small pair of scissors (nail cutters work

remarkably well), carefully cut and remove all four (4) zip ties listed above. DO NOT cut the
zip ties on the laser tube itself. Be aware that the glass laser tube is extremely fragile. Be
careful NOT to damage any part of the machine during this process.

Technical Support is available from 8:00 am (PST) to 5:00 pm (PST) Monday through Friday at

[email protected]

.

«
...
16
17
18
19
20
...
»

Содержание HL40-5g Hobby Advanced




























































































Отзывы:

Нет отзывов

Похожие инструкции для HL40-5g Hobby Advanced

Бренд: Makita Страницы: 372

Бренд: Makita Страницы: 19

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 28

Бренд: Makita Страницы: 11

Бренд: Makita Страницы: 24

Бренд: Ronix Страницы: 25

Бренд: Gardeo Страницы: 154

Бренд: Larzep Страницы: 5

Бренд: Fein Страницы: 1

Бренд: Logan Страницы: 16

Бренд: Ilco Orion Страницы: 26

Бренд: Kiwi Страницы: 8

TMC24 TURF multi Cutter

Бренд: Groundsman Страницы: 22

Бренд: US Cutter Страницы: 32

Бренд: Roto Zip Tool Страницы: 48

Бренд: RASOR Страницы: 15

Бренд: Stihl Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды