MAINTENANCE AND SERVICING
M2488 PRODUCT GUIDE
8-22
CG00000-011503 REV. A
April 1997
List
List [n] [e]
List [Regis-
try] [r] [t]
List current tests in test list or
list test registry. Entering “List”
will display all of the tests in the
current test list. Entering “List
Registry” will display the regis-
try of all of the tests available
for use in the current diagnostic
mode. The list command may be
aborted by pressing
<RETURN> before all tests are
displayed.
List arguments:
n -Node number in current test list to list, or being listing from. If n
is not specified or is an asterisk “*”, then the entire test list will be
displayed. If only n is specified, then only the test at that node
number will be displayed.
e -End node number in current list to stop listing at. If an asterisk
“*” is entered, all tests beginning with n will be displayed.
List Registry arguments:
r -Routine number in test registry to be displayed. If an asterisk
“*” is entered, then all routines in the current diagnostic mode will
be displayed.
t -Test number of routine r in test registry to be displayed. If an
asterisk “*” is entered, all tests for routine r will be displayed.
Options o:
[+/-] [c:e:s]
Set test options for all tests in
the current test list.
o -Options byte for this list of tests. The options byte is arranged
into bit fields as illustrated in the Table 8-18.
Quit
Quit Off-Line diagnostics
mode. (Entering this command
will cause a return to the previ-
ous operating mode.)
Run [macro]
[#]
Run tests in current test list. This
command is used to begin test
execution. Tests are executed in
sequential order beginning with
the first node. The test options
byte for each test may modify
execution behavior. At any point
during test list execution, the
operator may abort execution of
the test list at the conclusion of
the current test.
# - The number of times to execute the entire list of tests. By
default, the list will only execute one time. To loop forever, enter
0.
macro - One of several predetermined test lists. Macro names are
listed when entering “help macros” at the command line prompt.
Node n l
Set loop count for test at node #
n in the current test list
n - Node number to change loop count for. This number must be
in the range of node numbers in the current list.
l - Loop count, the number of times to repeat the test at the speci-
fied mode.
COMMAND
DESCRIPTION
VARIABLES/ARGUMENTS
Содержание M2488
