MEDIA CHANGER COMMANDS
M2488 PRODUCT GUIDE
6-2
CG00000-011503 REV. A
March 1997
6-2.1
EXCHANGE MEDIUM MC command A6h
The EXCHANGE MEDIUM medium-changer command provides a means to exchange the medium
in the source element, with the medium located at a destination element.
The medium in the source element is moved to the first destination element and the medium that pre-
viously occupied the first destination element is moved to the second destination element. The sec-
ond destination element may or may not be the same element as the source element. In the case of a
simple exchange, the source element and the second destination element are the same.
This device can emulate the capability of handling two units of media at the same time. The ACL
cannot perform exchange medium operations. The FACL can perform an exchange medium opera-
tions if the tape unit is empty.
6-2.1.1
EXCHANGE MEDIUM CDB Description
EXCHANGE MEDIUM is a twelve-byte command. The bytes are shown below and described in
the following paragraphs. Common fields are described in paragraph 4-3.1 on page 4-4.
This command will only accept Transport element addresses of 0000h (default) or 000Eh (Trans-
port Element address).
For this product, the Source address, First destination address, and Second destination addresses
are storage elements.
When the Source address, First destination address, and Second destination addresses have the
same value, this command performs no operation.
When the Source address and the First destination address have the same value and the second
destination addresses has a different value, you are attempting to perform a simple MOVE
MEDIUM and this EXCHANGE MEDIUM command is accepted.
The device capabilities page (XCL MODE parameters page 1Fh) provides a matrix which defines
the supported source element type and first destination element type combinations for
BITS
BYTES
7
6
5
4
3
2
1
0
0
1
0
1
0
0
1
1
0
1
LUN
Reserved
2-
3
MSB
Transport Element Address
LSB
4-
5
MSB
Source Address
LSB
6-
7
MSB
First Destination Address
LSB
8-
9
MSB
Second Destination Address
LSB
10
Reserved
11
Reserved
Flag
Link
Note: Changeable fields in the CDB are shaded.
Содержание M2488
