M2488 PRODUCT GUIDE
MAINTENANCE AND SERVICING
April 1997
CG00000-011503 REV. A
8-21
RS-232 User Interface Commands
Upon entering the Off-Line diagnostic mode, the command prompt
OFF-LINE DIAGNOSTIC COMMAND:
will appear. At the command prompt, the following commands are available.
a) Conventions used in this session:
All commands are case insensitive and may be abbreviated by entering only the first letter of the
command. The lower case letters immediately following the first letter are optional.
b) RS-232 command set:
Bold
Commands, options, variables, arguments, and user input appear in bold type-
face.
Italic
Names of variables to which values must be assigned are in italics.
< >
Input typed in a command line that does not appear on the screen (for example,
the return key) is shown within angle brackets.
[ ]
Optional input, such as command options, variables, and arguments, are
enclosed in square brackets.
COMMAND
DESCRIPTION
VARIABLES/ARGUMENTS
Add r t [l]
Add a new test to the end of the
test list.
r -Routine number to be added. This number must be a valid rou-
tine number from the routines listed in the test registry (see List
command for more details).
t -Test number of the routine to be added. If an asterisk “*” is
entered, all tests for the given routine will be added.
l -Loop count, number of times to repeat this test. This number
must be in the range between 1 and 254. If 0 is entered, the test
will loop forever.
Delete n [x]
Delete a test from the list of
tests.
n -Delete node number n from list. The node number must be a
number in the range of node numbers in the current list. If an aster-
isk “*” is entered, then the entire list is deleted.
x - Delete to this end node. (Default is “*”; to the end of the list.)
Help (or ?)
Help notes
Help macros
Display RS-232 user interface
command help. Entering this
command displays the help
information shown in Figure 8-
1.
Insert n r t [l]
Insert a new test in the test list.
n -Node number to insert. This number must be in the range of
node numbers in the current list.
r -Routine number to be added. This number must be a valid rou-
tine number from the routines listed in the test registry (see List
command for more details).
t -Test number of the routine to be added. If an asterisk “*” is
entered, all tests for the given routine will be added.
l -Loop count, number of times to repeat this test. This number
must be in the range between 1 and 254. If 0 is entered, the test
will loop forever.
Содержание M2488
