manualshive.com logo in svg

EXFO FTB-860, Руководство пользователя, Страница: 301 / 409

Поделиться
Скачать
EXFO FTB-860 Скачать руководство пользователя страница 301

Common Test Setup, Results, and Functions

NetBlazer

289

Interface - Network

Interface ID Coupled

: This field is available when the 

Global IPv6 

Address

 Mode is 

Static

. This field allows to couple the interface ID of 

the Global address to the Link-Local source address. 

Enable

 or 

Disable

 the 

Interface ID Coupled

. The default setting is 

Enabled

.

When the 

Interface ID Coupled

 is 

Enabled,

 only the 64 bit (MSB) 

prefix ID in the IPv6 address is configurable, and the 64 bit (LSB) 
Interface ID is not configurable (read-only). 

When the

 Interface ID Coupled

 is 

Disabled

, the 64 bit (MSB) Prefix ID 

and 64 bit (LSB) Interface ID in the IPv6 address are configurable.

Prefix Mask

: Enter the 

Prefix Mask

. This field is only configurable 

when the Global IPv6 Address Mode is Static. It allows to specify a 
prefix that defines the subnet. The accepted range is 

0000:0000:0000:0000:0000:0000:0000:0000

 to 

FFFF:FFFF:FFFF:FFFF:0000:0000:0000:0000

. For example:

Global Address: 2001:0DB8:0001:0002:02AA:00FF:FE11:1111

Prefix Mask: FFFF:FFFF:FFFF:0000:0000:0000:0000:0000 

Corresponding Prefix: 2001:0DB8:0001.

Default Gateway

: The 

Default Gateway

 tab allows the configuration of 

the default gateway address to forward packets outside the subnet.

Mode

: Select the 

Mode

 as 

Automatic

 or 

Static

.

Automatic

 allows automatic selection of the default gateway. The 

default setting is Automatic.

Static

 allows entering the default gateway IP address.

Address

: If the 

Mode

 is 

Static

, enter the IP address of the Default 

Gateway. The accepted range is from 

FE80:0000:0000:0000:0000:0000:0000:0000 

to 

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF

. The default address 

is 

FE80:0000:0000:0000:0000:0000:0000:0000

. When the Mode is 

Automatic

, the address field is not configurable.

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов