manualshive.com logo in svg

EXFO FTB-860, Руководство пользователя, Страница: 286 / 409

Поделиться
Скачать
EXFO FTB-860 Скачать руководство пользователя страница 286

Test Control

274

FTB-860/880

Lpbk Tool Button (Loopback Tool)

Loopback Mode

: The 

Loopback Mode

 parameter shall determine at 

which layer the address/port swapping is limited. Select the 

Loopback 

Mode

. Choices are:

UDP/TCP

: Swap MAC addresses, IP addresses, UDP or TCP ports 

when present and addressed to unit own MAC/IP. In other words, 
swap from Layer 2 up to Layer 4 when present.    

IP

: Swap MAC addresses, IP addresses when present and 

addressed to unit own MAC/IP. In other words, swap from Layer 2 
up to Layer 3 when present. 

Ethernet

: Swap MAC addresses when addressed to unit own MAC. 

In other words, swap Layer 2 when present.    

Ethernet (Unicast)

: Swap MAC addresses when the address is 

unicast, regardless if it is unit’s own MAC or not.    

Transparent

: Loopback everything without swapping anything. 

By default,

 UDP/TCP 

is selected.

Rate Unit

: Select the rate unit as 

%

, 

Mbit/s

,

 

or

 Gbit/s

 (when 

applicable).

Traffic

Total TX Rate

: Indicates the transmission rate as a percentage of 

the line rate (

%

), 

Mbit/s

, or

 Gbit/s 

(when applicable).

Total RX Rate

: Indicates the receive rate as a percentage of the 

line rate (

%)

, 

Mbit/s, 

or

 Gbit/s 

(when applicable).

Total TX Count

: The Total TX frame count includes all frames 

transmitted. 

Total RX Count

: The Total RX frame count includes all frames 

received. 

Loopback

 button: Starts/Stops the Loopback Tool to loopback the 

frames/packets that are received. The default value is disabled. 

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов