EXFO FTB-860 Скачать руководство пользователя страница 288

Страница: 288 / 409

Test Control

276

FTB-860/880

Lpbk Tool Button (Loopback Tool)



Cable Mode:

Select

Cable Mode

if the

Interface Type

is Electrical.

Choices are

Auto Detect

and

Manual

. If

Manual

is selected, go to

the next field and select the type of cable (

MDI

for straight through,

MDIX

for crossover).

Note:

Cable Mode is not available when Auto-Negotiation is enabled.



Clock Mode

: Displays the mode of the clock when

10G LAN

interface type is selected.

Recovered:

Live clock from the optical port input signal involved

in the tool. Recovered is the only available clock with

Loopback

test.



Frequency (MHz)

: Indicates the frequency of the input signal in

MHz

. When no frequency reading is possible, “

” is displayed.



Link



Auto-Negotiation:

Enable

Auto-Negotiation

, if the remote

connected port is also set to

Auto-Negotiation

, otherwise it should

be disabled. This is available only with the

10/100/1000 Mbit/s

Electrical

interface.



Speed

: Select the

Speed

of the interface. This is available only with

the

10/100/1000 Mbit/s Electrical

interface.

Note:

Speed is not available for optical interfaces.

Note:

When Speed is configured as

Auto

, the negotiated speed is displayed

beside the speed configuration parameter.



Duplex

: Select the

Duplex

mode when

Auto-Negotiation

Enabled

. For

10 Mbit/s

and

100 Mbit/s

electrical interfaces,

choices are

Full

(default), and

Auto

. For

1000 Mbit/s

electrical

interface, the duplex is set to

Full

Содержание FTB-860


























































































































































































































































































































































































































Результаты поиска

Содержание FTB-860

Отзывы:

EXFO FTB-860, Руководство пользователя, Страница: 288 / 409

Результаты поиска

Содержание FTB-860

Отзывы: