manualshive.com logo in svg

EXFO FTB-860, Руководство пользователя, Страница: 220 / 409

Поделиться
Скачать
EXFO FTB-860 Скачать руководство пользователя страница 220

SyncE Test Setup and Results

208

FTB-860/880

Summary (SyncE)

RX

Last QL Message

 indicates the last Quality Level value received. The 

pass/fail verdict is also displayed when both 

QL Mismatch Monitoring

 

and 

Pass/Fail Verdict

 check boxes are selected. 

Last Change

 indicates the date and time of the Last QL Message has 

changed. 

Information/Event Count 

gives respectively the count of information 

and event frames generated for all Quality Level values. 

QL Mismatch Frame Count

 gives the total count of information and/or 

event frames received not matching the expected Quality Level. Only 
available when the 

QL Mismatch Monitoring

 check box is selected. 

Frequency/Offset 

indicates respectively the frequency and the offset 

between the standard rate specification and the rate

 

of the input signal. 

Max. (-/+) Offset (ppm)

 indicates respectively the minium and 

maximum offset between the standard rate specification and the 
largest/smallest rate recorded from the received signal. 

TX

QL Message 

indicates the Quality Level value that is generated. 

Last Change

 indicates the date and time of the QL Message value has 

changed. For 1GE Electrical interface using 

Local Clock

 set to 

Slave

, 

the 

Last Change

 is not available. 

Information/Event Count 

gives respectively the count of information 

and event frames generated for all Quality Level values. 

Event Count

 is 

not available with 1GE Electrical interface using remote local clock. 

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов