Epson S1C17602 Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 368

background image

18 uaRT

18-10

Seiko epson Corporation

S1C17624/604/622/602/621 TeChniCal Manual

D0

TDBe: Transmit Data Buffer empty Flag Bit

Indicates the transmit data buffer status.

1 (R):

Buffer empty (default)

0 (R):

Data exists

TDBE is reset to 0 when transmit data is written to the transmit data buffer and is set to 1 when the data
is transferred to the shift register.

uaRT Ch.

x

Transmit Data Registers (uaRT_TXD

x

)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

uaRT Ch.

x

Transmit Data
Register
(uaRT_TXD

x

)

0x4101
0x4121

(8 bits)

D7–0 TXD[7:0]

Transmit data
TXD7(6) = MSB
TXD0 = LSB

0x0 to 0xff (0x7f)

0x0 R/W

D[7:0]

TXD[7:0]: Transmit Data

Write transmit data to be set in the transmit data buffer. (Default: 0x0)

The UART starts transmitting when data is written to this register. Data written to TXD[7:0] is retained
until sent to the transmit data buffer. Transmitting data from within the transmit data buffer generates a
cause of transmit buffer empty interrupt.

TXD7 (MSB) is invalid in 7-bit mode.

Serial converted data is output from the SOUT

x

pin beginning with the LSB, in which the bits set to 1

are output as High level and bits set to 0 as Low level signals.

This register can also be read.

uaRT Ch.

x

Receive Data Registers (uaRT_RXD

x

)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

uaRT Ch.

x

Receive Data
Register
(uaRT_RXD

x

)

0x4102
0x4122

(8 bits)

D7–0 RXD[7:0]

Receive data in the receive data
buffer
RXD7(6) = MSB
RXD0 = LSB

0x0 to 0xff (0x7f)

0x0

R Older data in the buf-

fer is read out first.

D[7:0]

RXD[7:0]: Receive Data

Data in the receive data buffer is read out in sequence, starting with the oldest. Received data is placed in
the receive data buffer. The receive data buffer is a 2-byte FIFO that allows proper data reception until it
fills, even if data is not read out. If the buffer is full and the shift register also contains received data, an
overrun error will occur, unless the data is read out before reception of the subsequent data starts.

The receive circuit includes two receive buffer status flags: RDRY/UART_ST

x

register and RD2B/

UART_ST

x

register. The RDRY flag indicates the presence of valid received data in the receive data

buffer, while the RD2B flag indicates the presence of two received data in the receive data buffer.

A receive buffer full interrupt occurs when the received data in the receive data buffer reaches the num-
ber specified by RBFI/UART_CTL

x

register.

0 is loaded into RXD7 in 7-bit mode.

Serial data input via the SIN

x

pin is converted to parallel, with the initial bit as LSB, the High level bit

as 1, and the Low level bit as 0. This data is then loaded into the receive data buffer.

This register is read-only. (Default: 0x0)

uaRT Ch.

x

Mode Registers (uaRT_MOD

x

)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

uaRT Ch.

x

Mode Register
(uaRT_MOD

x

)

0x4103
0x4123

(8 bits)

D7–5 –

reserved

–

–

–

0 when being read.

D4

Chln

Character length select

1 8 bits

0 7 bits

0

R/W

D3

PRen

Parity enable

1 With parity

0 No parity

0

R/W

D2

PMD

Parity mode select

1 Odd

0 Even

0

R/W

D1

STPB

Stop bit select

1 2 bits

0 1 bit

0

R/W

D0

SSCK

Input clock select

1 External

0 Internal

0

R/W

D[7:5]

Reserved

«
...
193
194
195
196
197
...
»

Содержание S1C17602

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C17602

Бренд: ZKTeco Страницы: 123

Бренд: S-COM Страницы: 400

Бренд: halstrup-walcher Страницы: 39

Бренд: Eaton Страницы: 8

Бренд: ABB Страницы: 44

Бренд: Omega Страницы: 2

Бренд: Zmotion Страницы: 34

Бренд: Davey Страницы: 12

Бренд: Watlow Страницы: 20

SYSVRF AHU 10HP S

Бренд: SystemAir Страницы: 16

Бренд: Zapi Страницы: 30

Бренд: Danfoss Страницы: 36

Бренд: SLV Страницы: 11

Бренд: Washify Страницы: 25

Бренд: microHAM Страницы: 64

Бренд: H3C Страницы: 15

Бренд: Brooks Страницы: 62

Бренд: Trane Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды