Epson S1C17602 Скачать руководство пользователя страница 257 | Manualshive

Страница: 257 / 368

background image

23 lCD DRiVeR (lCD)

23-14

Seiko epson Corporation

S1C17624/604/622/602/621 TeChniCal Manual

lCD interrupt

23.7

The LCD module includes a function for generating interrupts using the frame signal.

Frame interrupt

This cause of interrupt occurs every frame and sets the interrupt flag FRMIF/LCD_IFLG register in the LCD
module to 1. See Figures 23.4.2.1 to 23.4.2.5 for interrupt timings.

To use this interrupt, set FRMIE/LCD_IMSK register to 1. When FRMIE is set to 0 (default), interrupt requests
for this interrupt cause are not sent to the interrupt controller (ITC).

If FRMIF is set to 1 while FRMIE is set to 1 (interrupt enabled), the LCD module outputs an interrupt request
to the ITC. An interrupt is generated if the ITC and S1C17 Core interrupt conditions are satisfied.

For more information on interrupt processing, see the “Interrupt Controller (ITC)” chapter.

notes: • To prevent interrupt recurrences, the LCD module interrupt flag FRMIF must be reset in the

interrupt handler routine after an LCD interrupt has occurred.

• To prevent unwanted interrupts, FRMIF should be reset before enabling LCD interrupts with

FRMIE.

Control Register Details

23.8

8.1 List of LCD Registers

Table 23.

address

Register name

Function

0x5063

OSC_LCLK

LCD Clock Select Register

Selects the LCD clock.

0x50a0

LCD_DCTL

LCD Display Control Register

Controls the LCD display.

0x50a1

LCD_CADJ

LCD Contrast Adjustment Register

Controls the contrast.

0x50a2

LCD_CCTL

LCD Clock Control Register

Controls the LCD drive duty.

0x50a3

LCD_VREG

LCD Voltage Regulator Control Register

Controls the LCD drive voltage regulator.

0x50a5

LCD_IMSK

LCD Interrupt Mask Register

Enables/disables interrupts.

0x50a6

LCD_IFLG

LCD Interrupt Flag Register

Indicates/resets interrupt occurrence status.

The LCD module registers are described in detail below. These are 8-bit registers.

note: When data is written to the registers, the “Reserved” bits must always be written as 0 and not 1.

lCD Clock Select Register (OSC_lClK)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

lCD Clock
Select Register
(OSC_lClK)

0x5063

(8 bits)

D7–5 –

reserved

–

–

–

0 when being read.

D4–2 lCKDV[2:0] LCD clock division ratio select

LCKDV[2:0]

Division ratio

0x0 R/W When the clock

source is HSCLK

0x7–0x5

0x4
0x3
0x2
0x1
0x0

reserved

1/512
1/256
1/128

1/64
1/32

D1

lCKSRC

LCD clock source select

1 OSC1

0 HSCLK

1

R/W

D0

lCKen

LCD clock enable

1 Enable

0 Disable

0

R/W

D[7:5]

Reserved

D[4:2]

lCKDV[2:0]: lCD Clock Division Ratio Select Bits

Selects the division ratio when HSCLK (IOSC or OSC3) is selected as the LCD clock source.

«
...
255
256
257
258
259
...
»

Содержание S1C17602

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C17602

Бренд: Danfoss Страницы: 36

Бренд: Rachio Страницы: 2

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: WINDY NATION Страницы: 16

Бренд: e-survey Страницы: 12

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренд: Eaton Страницы: 2

Бренд: Current Страницы: 4

Бренд: PEAS Страницы: 4

Бренд: Sollae Systems Страницы: 72

Бренд: Melexis Страницы: 13

Бренд: Harsen Страницы: 55

Бренд: Wabtec Страницы: 5

Бренд: AMX Страницы: 2

Alicat Scientific IVCD

Бренд: Halma Страницы: 28

Бренд: Hall Research Technologies Страницы: 16

MotionWorks IEC

Бренд: YASKAWA Страницы: 21

Бренд: Intersil Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды