Epson S1C17602 Скачать руководство пользователя страница 283

Страница: 283 / 368

25 R/F COnVeRTeR (RFC)

S1C17624/604/622/602/621 TeChniCal Manual

Seiko epson Corporation

25-9

The R/F converter registers are described in detail below.

note: When data is written to the registers, the “Reserved” bits must always be written as 0 and not 1.

RFC Clock Control Registers (OSC_RFC)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

RFC Clock
Control Register
(OSC_RFC)

0x5067

(8 bits)

D7–4 –

reserved

–

0 when being read.

D3–2 RFTCKDV

[1:0]

RFC clock division ratio select

RFTCKDV[1:0] Division ratio

0x0 R/W When the clock

source is HSCLK

0x3
0x2
0x1
0x0

1/8
1/4
1/2
1/1

RFTCKSRC RFC clock source select

1 OSC1

0 HSCLK

R/W

RFTCKen RFC clock enable

1 Enable

0 Disable

R/W

D[7:4]

Reserved

D[3:2]

RFTCKDV[1:0]: RFC Clock Division Ratio Select Bits

Selects the division ratio for generating the TCCLK clock when HSCLK (IOSC or OSC3) is used as the
clock source.

8.2 HSCLK Division Ratio Selection

Table 25.

RFTCKDV[1:0]

Division ratio

0x3

1/8

0x2

1/4

0x1

1/2

0x0

1/1

(Default: 0x0)

RFTCKSRC: RFC Clock Source Select Bit

Selects the count clock source.

1 (R/W): OSC1 (default)

0 (R/W): HSCLK (IOSC or OSC3)

RFTCKen: RFC Clock enable Bit

Enables or disables the TCCLK clock supply.

1 (R/W): Enabled (on)

0 (R/W): Disabled (off) (default)

The RFTCKEN default setting is 0, which disables the clock supply. Setting RFTCKEN to 1 sends the
clock selected to the R/F converter.

RFC Control Register (RFC_CTl)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

RFC Control
Register
(RFC_CTl)

0x53a0

(16 bits)

D15–8 –

reserved

–

0 when being read.

COnen

Continuous oscillation enable

1 Enable

0 Disable

R/W

eVTen

Event counter mode enable

1 Enable

0 Disable

R/W

D5–4 SMODe[1:0] Sensor oscillation mode select

SMODE[1:0]

Sensor

0x0 R/W

0x3
0x2
0x1
0x0

reserved

DC capacitive

AC resistive
DC resistive

D3–2 –

reserved

–

0 when being read.

ChSel

Conversion channel select

1 Ch.1

0 Ch.0

R/W

RFCen

RFC enable

1 Enable

0 Disable

R/W

D[15:8] Reserved

COnen: Continuous Oscillation enable Bit

Enables continuous oscillation by disabling the automatic CR oscillation stop function.

1 (R/W): Continuous oscillation enabled

0 (R/W): Continuous oscillation disabled (default)

Содержание S1C17602

















































































































































































































































































































































































Результаты поиска

Содержание S1C17602

Отзывы:

Похожие инструкции для S1C17602

Бренды по названию

Популярные бренды

Epson S1C17602, Техническое руководство

Результаты поиска

Содержание S1C17602

Отзывы:

Похожие инструкции для S1C17602

Бренды по названию

Популярные бренды