manualshive.com logo in svg

Epson S1C17602, Техническое руководство

Эпсон S1C17602 - мощный микроконтроллер для различных устройств. Ознакомьтесь с техническим руководством, чтобы получить подробную информацию о функциях и возможностях этого устройства. Скачайте бесплатное руководство пользователя с нашего сайта, чтобы использовать все возможности Epson S1C17602.

Поделиться
Скачать
background image

6  inTeRRuPT COnTROlleR (iTC)

6-4

 

Seiko epson Corporation 

S1C17624/604/622/602/621 TeChniCal Manual

note:  The  MISC_TTBRL  and  MISC_TTBRH  registers  are  write-protected.  Before  these  registers  can 

be rewritten, write protection must be removed by writing data 0x96 to the MISC_PROT register. 
Note that since unnecessary rewrites to the MISC_TTBRL and MISC_TTBRH registers could lead 
to erratic system operation, the MISC_PROT register should be set to other than 0x96 unless the 
Vector Table Base Registers must be rewritten.

Control of Maskable interrupts

6.3  

interrupt Control Bits in Peripheral Modules

6.3.1  

The peripheral module that generates interrupts includes an interrupt enable bit and an interrupt flag for each inter-
rupt cause. The interrupt flag is set to 1 when the cause of interrupt occurs. By setting the interrupt enable bit to 1 
(interrupt enabled), the flag state will be sent to the ITC as an interrupt request signal, generating an interrupt re-
quest to the S1C17 Core. 
The corresponding interrupt enable bits should be set to 0 for those causes for which interrupts are not desired. In 
this case, although the interrupt flag is set to 1 if the interrupt cause occurs, the interrupt request signal sent to the 
ITC will not be asserted.
For specific information on causes of interrupts, interrupt flags, and interrupt enable bits, refer to the respective pe-
ripheral module descriptions.

note:  To prevent recurrence of the interrupt due to the same cause of interrupt, always reset the inter-

rupt flag in the peripheral module before enabling the interrupt, resetting the PSR, or executing 
the 

reti

 instruction.

iTC interrupt Request Processing

6.3.2  

On receiving an interrupt signal from a peripheral module, the ITC sends the interrupt request, interrupt level, and 
vector number signals to the S1C17 Core.
Vector numbers are determined by the ITC internal hardware for each interrupt cause, as shown in Table 6.2.1.
The interrupt level is a value used by the S1C17 Core to compare with the IL bits (PSR). This interrupt level is used 
in the S1C17 Core to disable subsequently occurring interrupts with the same or lower level. (See Section 6.3.3.)
The default ITC settings are level 0 for all maskable interrupts. Interrupt requests are not accepted by the S1C17 
Core if the level is 0.
The ITC includes control bits for selecting the interrupt level, and the level can be set to between 0 (low) and 7 (high) 

interrupt levels for each interrupt type.
If interrupt requests are input to the ITC simultaneously from two or more peripheral modules, the ITC outputs the 

interrupt request with the highest priority to the S1C17 Core in accordance with the following conditions.
1.  The interrupt with the highest interrupt level takes precedence.
2.  If multiple interrupt requests are input with the same interrupt level, the interrupt with the lowest vector number 

takes precedence.

The other interrupts occurring at the same time are held until all interrupts with higher priority levels have been ac-
cepted by the S1C17 Core.
If an interrupt cause with higher priority occurs while the ITC is outputting an interrupt request signal to the S1C17
Core (before being accepted by the S1C17 Core), the ITC alters the vector number and interrupt level signals to the 
setting information on the more recent interrupt. The previously occurring interrupt is held. The held interrupt is 
canceled and no interrupt is generated if the interrupt flag in the peripheral module is reset with software.

Содержание S1C17602

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C17602

UE 120 Series Installation And Maintenance Instructions preview
120 Series
Бренд: UE Страницы: 4
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Бренд: Danfoss Страницы: 128
IAI ROBO Cylinder RCP2 Series Quick Start Manual preview
ROBO Cylinder RCP2 Series
Бренд: IAI Страницы: 5
Vaillant VSMART User Manual preview
VSMART
Бренд: Vaillant Страницы: 11
ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Бренд: ABB Страницы: 17
Zander Aachen ZX20T Operating Manual preview
ZX20T
Бренд: Zander Aachen Страницы: 44
Samson TROVIS 5571 Mounting And Operating Instructions preview
TROVIS 5571
Бренд: Samson Страницы: 44
Beckhoff C6925 Manual preview
C6925
Бренд: Beckhoff Страницы: 47
DOTECH FX3DH Series Manual preview
FX3DH Series
Бренд: DOTECH Страницы: 4
MISUMI DS102MS Operation Manual preview
DS102MS
Бренд: MISUMI Страницы: 166
Sunricher SR-2400P Quick Start Manual preview
SR-2400P
Бренд: Sunricher Страницы: 2
Danfoss PVE Series Installation Manual preview
PVE Series
Бренд: Danfoss Страницы: 6
SSHC TSSHC-3IL-24 Quick Start Manual preview
TSSHC-3IL-24
Бренд: SSHC Страницы: 2
Citadele Digipass 320 Operation Instructions Manual preview
Digipass 320
Бренд: Citadele Страницы: 6
Grifco C10A Installation And User Manual preview
C10A
Бренд: Grifco Страницы: 20
Daktronics All Sport 1600 Series Operation Manual preview
All Sport 1600 Series
Бренд: Daktronics Страницы: 92
YASKAWA Sigma-7Siec Hardware Manual preview
Sigma-7Siec
Бренд: YASKAWA Страницы: 38
S2Tech 699PLUS Instruction Manual preview
699PLUS
Бренд: S2Tech Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды