manualshive.com logo in svg

Emerson DSM314, Руководство пользователя, Страница: 429 / 519

Поделиться
Скачать
Emerson DSM314 Скачать руководство пользователя страница 429

User Manual 

Appendix D 

GFK-1742F 

Jan 2020 

 

Tuning Digital and Analog Servo Systems 

418 

Appendix D:

 

Tuning Digital and Analog Servo 

Systems 

This  appendix  provides  a  procedure  for  starting  up  and  tuning  a  Digital  or  Analog  servo 
system. For Digital servos systems, there are two control loops in the DSM314 that require 
tuning, the velocity loop and the position loop. Always begin with module configuration 
then  proceed  to  the  velocity  loop  setting  and  finally  the  position  loop.  For  Analog  servo 
systems, there are a series of Start-Up Procedures to follow. 

D-1

 

Start-Up  and  Tuning  Information  for  Digital 
Servo Systems 

There are three major sections covered: 

•

 

Validating Home Switch, Over Travel Inputs and Motor direction. 

•

 

Tuning the Velocity Loop. 

•

 

Tuning the Position Loop. 

D-1.1

 

Validating  Home  Switch,  Over  Travel  Inputs  and  Motor 
direction 

1.

 

Connect  the  motor,  amplifier  and  DSM314  module  following  the  procedures  in 
Chapter 2. 

2.

 

If  Over  travel  Limit  switches  are  used  (Overtravel  Limit  Switch  =  Enabled  in 
configuration), wire them to the correct 24V terminal board points (refer to Chapter 
3). The overtravel inputs are operated in the fail-safe mode i.e. a normally closed or 
PNP type switching device should be used.  Current must be sourced to the input to 
maintain a logic level 1 on the input while the axis is NOT at the overtravel position 
or an alarm condition (Error A9) will be returned.  Otherwise the  Overtravel Limit 
Switch configuration must be set to Disabled using the configuration software. 

3.

 

If a Home switch is used (Home Mode = Home Switch in configuration), wire it to the 
correct 24V terminal board points (refer to Chapter 3). The Home switch must be 
wired and actuated so that it is ALWAYS ON (closed) when the axis is on the negative 
side of home and ALWAYS OFF (open) when the axis is on the positive side of home. 
Typically,  the  Home  switch  is  mounted  at  or  near  one  end  of  the  axis  travel.  It  is 
important to verify the operation of the home switch prior to attempting a home 
cycle. It may be necessary to reverse the motor direction (Motor1 or Motor2 Dir = 
POS/NEG) in the module configuration. 

 

 

 

Содержание DSM314








































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов