Emerson DSM314 Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 519

Emerson DSM314 Скачать руководство пользователя страница 164

User Manual

Chapter 5

GFK-1742F

Jan 2020

DSM314 to Host Controller Interface

153

The data field for this command may contain a parameter number in byte 2 (bytes
3-5 unused) with the command type as defined below:

Move Type (byte 1):

80h = Abs, Pmove, Linear

81h = Abs, Cmove, Linear

90h = Abs, Pmove, Scurve

91h = Abs, Cmove, Scurve

C0h = Inc, Pmove, Linear

C1h = Inc, Cmove, Linear

D0h = Inc, Pmove, Scurve

D1h = Inc, Cmove, Scurve

The Move Command is executed as a single move motion program. Therefore, all
the restrictions that apply to motion program execution also apply to the Move
Command. For example, if a program is already active for axis 1, then an attempt to
send this command for axis 1 will result in an error condition being reported.

4.10 Jog Velocity. (User units/sec) This command sets the velocity used when a Jog %Q

bit is used to jog in the positive or negative direction. Jog Velocity is used by motion
programs when no Velocity command is included in the program. Jog Velocity is
always used by the %AQ Move Command (27h). A host controller reset, or power
cycle returns this value to the configured data.

4.11 Jog Acceleration. (User units/sec/sec) This command sets the acceleration value

used by Jog, Find Home, Move at Velocity, Abort All Moves and Normal Stop
operations. A Normal Stop occurs when the host controller switches from Run to
Stop or after certain programming errors (refer to Appendix A). Jog Acceleration is
used by motion programs when no Acceleration command is included in the
program. Jog Acceleration is always used by the %AQ Move Command (27h). A host
controller reset, or power cycle returns this value to the configured data.

Note:

A minimum value after scaling is used in the DSM314. This value is determined by the
rule:

Jog Acc * (user units/counts) >= 32 counts/sec/sec.

4.12 Position Loop Time Constant. (0.1 Milliseconds) This command allows the servo

position loop time constant to be changed from the configured value. The lower the
Position Loop Time Constant value, the faster the system response. Values that are
too low will cause system instability and oscillation. For accurate tracking of the
commanded velocity profile, the Position Loop Time Constant should be 1/4 to 1/2
of the MINIMUM system acceleration or deceleration time. For Analog mode, the

“Vel at Max Cmd” configuration value must be set correctly for proper operation of

the Position Loop Time Constant. A host controller reset, or power cycle returns this
value to the configured data.

«
...
162
163
164
165
166
...
»

Содержание DSM314








































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов