manualshive.com logo in svg

Emerson DSM314, Руководство пользователя, Страница: 124 / 519

Поделиться
Скачать
Emerson DSM314 Скачать руководство пользователя страница 124

User Manual 

Chapter 4 

GFK-1742F 

Jan 2020 

 

Configuration 

113 

5.03  Drive Ready Input. Enables or disables the Drive Ready input for Analog Servos. This 

configuration item is ignored for a Digital Servo or Auxiliary axis, If the Drive Ready 
input is enabled, the Drive Ready faceplate input signal (IN4) must be turned on (set 
to 0v) within 1 second after the Enable Drive %Q bit is turned on. If the Drive Ready 
faceplate input is turned off while the Drive Enabled %I bit is on, error code C0h will 
be reported and the axis will stop. The Drive Ready Input configuration should be set 
to Disabled for Analog Servos that do not provide a compatible Drive Ready output 
signal. 

5.04  High Position Limit. (User Units). When moving in the positive direction, the Actual 

Position will roll over to the low limit when this value is reached. The Position Limits 
can  be  used  for  continuous  rotary  applications  when  the  Software  End  of  Travel 
configuration is set to Disabled. The High Position Limit should always be set one 
User Unit smaller than the desired cycle. For example, a 360° machine would have a 
High Position Limit setting of 359. At the next count past 359, the count would roll 
over to the value set in the Low Position Limit parameter (0 in this example). For 
proper operation, the rollover modulus (High Position Limit - Low Position Limit +1) 
must always be greater than the distance traveled by the axis in one position loop 
sample  time  (normally  2  ms).  See  Appendix  C  for  considerations  when  using  an 
absolute mode encoder. Default: 8,388,607. 

5.05  Low  Position  Limit.  Low  Pos  Limit  (User  Units).  When  moving  in  the  negative 

direction,  the  Actual  Position  will  roll  over  to  the  high  limit  when  this  value  is 
reached. . The Position Limits can be used for continuous rotary applications when 
the Software End of Travel configuration is set to Disabled. For proper operation, the 
rollover  modulus  (High  Position  Limit  -  Low  Position  Limit  +1)  must  always  be 
greater  than  the  distance  traveled  by  the  axis  in  one  position  loop  sample  time 
(normally 2 ms). See Appendix C for considerations when using an absolute mode 
encoder. Default: - 8,388,608. 

5.06  High Software EOT Limit. High Software End of Travel Limit (User Units). If the limit 

is enabled and the DSM314 is programmed to go to a position greater than the High 
Software EOT value, an error will result and the DSM314 will not allow axis motion. 
If the Follower control loop is enabled, the High Software EOT Limit is ignored for 
slave axis motion resulting from master axis commands. The limit only applies to 
slave  axis  motion  resulting  from  internally  generated  jog  and  motion  program 
commands.  The  limit  is  always  ignored  for  Move  at  Velocity  %AQ  commands. 
Default: +8,388,607. 

In Analog or Digital Servo modes, the High Software EOT limit is used only when the 
Software End of Travel configuration is set to Enabled. If the High Software EOT Limit 
is  enabled  and  its  value  is  more  positive  than  the  High  Position  Limit,  the  High 
Software EOT Limit will internally be set equal to the High Position Limit. Axis error 
code 17h will also be reported, indicating that the limit has been adjusted. The High 
Software EOT Limit is ignored for Jog commands if the Position Valid %I bit is off. 

In  Auxiliary  Axis  mode,  the  High  Software  EOT  limit  has  separate  purposes 
depending on the setting for Software End of Travel: 

Содержание DSM314








































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов