manualshive.com logo in svg

Ditch Witch JT5, Руководство оператора

Поделиться
Скачать
Ditch Witch JT5 Скачать руководство пользователя страница 90

JT5 Operator’s Manual

Systems and Equipment - 89

Electric Strike System

CMW

®

Electric Strike System

Any time you drill in an electric jobsite, electric strike system must be properly set up, tested, and used. 

You must wear protective boots and gloves meeting the following standards:

•

Boots must have high tops and meet the electric hazard protection requirements of ASTM F2413 or 

ASTM F1117when tested at 14,000 volts. Tuck legs of pants completely inside boots. 

•

Gloves must have 17,000 AC maximum use voltage, according to ASTM specification D120.

If working around higher voltage, use gloves and boots with appropriately higher ratings.

Read and follow “Electric Jobsite Precautions” on page 47. Review safety procedures before each job.

FCC Statement

The Electric Strike System has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the 
FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated 
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used 
in accordance with the instructions, can cause harmful interference to radio communications. Operation of this equipment in a 
residential area could cause harmful interference which the user will be required to correct at his own expense.

Changes or modifications not expressly approved in writing by The Charles Machine Works, Inc. may void the user's authority to 
operate this equipment.

NOTICE: 

The strike system does not prevent electric strikes or detect strikes before they occur. 

If 

alarms are activated, a strike has already occurred

 and equipment is electrified.

Содержание JT5




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды