Ditch Witch JT5 Скачать руководство пользователя страница 95

Страница: 95 / 155

Systems and Equipment - 94

JT5 Operator’s Manual

Electric Strike System

CMW

Use Electric Strike Simulator

Use the Electric Strike Simulator (p/n 259-506) to test voltage and current sensors on ESID. If readings are
less than indicated here, replace 9V battery in simulator and retest.

Current Test

To test for current at normal levels:

Thread one lead wire through current transformer.

Clip ends of lead wires together to make one loop.

Move simulator switch to "current" and press test button.

Watch screen and lights above display on strike system.

•

Three or four lights should turn on.

•

Current "A" should show 30-50% in display.

EV2 code displays and
voltage problem indicator is
on

Improper connections with
control module

Check cable connection on control
module

Defective voltage limiter

Have voltage limiter checked or
replaced

Defective control module

Have control module checked or
replaced

Problem

Possible cause

Possible solution

Содержание JT5




























































































































































Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch JT5, Руководство оператора

Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды