Ditch Witch JT5 Скачать руководство пользователя страница 45

Страница: 45 / 155

Prepare - 44

Manual

Inspect Site

CMW

Inspect Site

Inspect jobsite before transporting equipment. Check for the following:

•

overall grade or slope

•

changes in elevation such as hills or open trenches

•

obstacles such as buildings, railroad crossings, or streams

•

signs of utilities (See “Inspect Jobsite” on page 46.)

•

traffic

•

access

•

soil type and condition

•

water supply

•

sources of locator interference (rebar, railroad tracks, etc.)

Take soil samples from several locations along bore path to determine best bit and backreamer
combinations.

Identify Hazards

Identify safety hazards and classify jobsite. See “Classify Jobsite” on page 46.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

274-050; 274-724 (2P)

To help avoid injury:

•

Wear personal protective equipment including hard hat, safety eye wear, and hearing protection.

•

Do not wear jewelry or loose clothing.

•

Notify One-Call and companies which do not subscribe to One-Call.

•

Comply with all utility notification regulations before digging or drilling.

•

Verify location of previously marked underground hazards.

•

Mark jobsite clearly and keep spectators away.

Remember, jobsite is classified by hazards in place -- not by line being installed.

Содержание JT5




























































































































































Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch JT5, Руководство оператора

Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды