manualshive.com logo in svg

Ditch Witch JT5, Руководство оператора

Поделиться
Скачать
Ditch Witch JT5 Скачать руководство пользователя страница 127

Service - 126

JT5 Operator’s

 

Manual

Startup/10 Hour

CMW

®

Check Hydraulic Hoses 

Check hydraulic hoses for leaks before startup and 
every 10 hours of operation.

 

Pressurized fluid or air could pierce skin and cause severe 

injury. Refer to operator’s manual for proper use.   

270-6035

 

To help avoid injury:

 Escaping pressurized fluid can cause injury or pierce skin and poison.

•

Before disconnecting a hydraulic line, turn engine off and operate all controls to relieve pressure. 
Lower, block, or support any raised component with a hoist. Cover connection with heavy cloth and 
loosen connector nut slightly to relieve residual pressure. Catch all fluid in a container.

•

Before using system, check that all connections are tight and all lines are undamaged.

•

Fluid leaks can be hard to detect. Use a piece of cardboard or wood, rather than hands, to search for 
leaks.

•

Wear protective clothing, including gloves and eye protection.

•

If you are injured, seek immediate medical attention from a doctor familiar with this type of injury.

Содержание JT5




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды