Ditch Witch JT5 Скачать руководство пользователя страница 122

Страница: 122 / 155

JT5 Operator’s

Manual

Service - 121

Service Precautions

CMW

Working Under Drilling Unit

Before working under area of drilling unit
supported by a stabilizer, make sure drilling unit is
parked on hard surface.

Remove yellow cylinder lock from storage at
rear of pipe box and place over extended
cylinder rod (shown) with curved ends toward
stabilizer shoe.

Raise stabilizer to lower unit until load is
supported by cylinder lock.

Opening/Closing Front Hood

To open

Unlock hood at outside latches (1).

Press key lock buttons to release latches and
tip hood toward you.

Lift hood to remove.

To close

1. Align pins (2) with designated holes.

Secure latches (1). Lock if necessary.

Crushing weight could cause death or serious injury. Use

proper procedures and equipment or stay away.

Содержание JT5




























































































































































Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch JT5, Руководство оператора

Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды