manualshive.com logo in svg

Ditch Witch JT5, Руководство оператора

Поделиться
Скачать
Ditch Witch JT5 Скачать руководство пользователя страница 53

Prepare - 52

Manual

Plan Bore Path

CMW

®

Entry Pitch

Entry pitch is the slope of the drill frame compared with the slope of the ground. Determine entry pitch one 
of two ways:

1.

With Pitch Beacon

•

Lay pitch beacon on the ground and read 
pitch.

•

Lay pitch beacon on drill frame and read pitch.

•

Subtract ground pitch from drilling unit pitch.

2.

With Measurements

•

Measure from the ground to front end of drill 
frame (H1).

•

Measure from the ground to back end of frame 
(H2).

•

Subtract (H1) from (H2). Record this number.

•

Measure the distance between front and back 
points (C).

•

Divide (H2-H1) by (C), then multiply by 100. 
This is your pitch.

 

Minimum Setback

Setback is the distance from the entry point to where 
pipe becomes horizontal (B1).

IMPORTANT: 

A shallow entry pitch (A1) allows you 

to reach horizontal sooner and with less bending. 
Increasing entry pitch (A2) makes bore path longer 
and deeper.

NOTICE: 

If setback is too small (B2), you will 

exceed bend limits and damage the pipe.

Содержание JT5




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды