manualshive.com logo in svg

Ditch Witch JT5, Руководство оператора

Поделиться
Скачать
Ditch Witch JT5 Скачать руководство пользователя страница 92

JT5 Operator’s Manual

Systems and Equipment - 91

Electric Strike System

CMW

®

ESID Diagnostic Codes

When strike system detects a problem, an error code will be displayed. Anytime this happens, press self 
test button to retest. If error code is still displayed and does not appear in this chart, have control module 
checked or replaced.   

Code

Display

Condition

Result

502

2.5V REF

2.5V reference error in ESID

internal reference failure, ESID may not 
give valid readings

503

-5V REF

-5V reference error in ESID

internal reference failure, ESID may not 
give valid readings

504

CLK RESP

clock response error

clock may not be working

505

LCD RESP

LCD response error

LCD display may not work

506

LED RESP

LED response error

LED display may not work

507

LCD CONTR

LCD contrast error

LCD contrast not saved properly

508

COP RESET

cop watchdog error

processor has reset, unknown status of 
ESID code

510

STRB DVR

strobe driver output error

strobe may not function

511

HORN DVR

horn driver output error

horn may not function

512

BAT POWER

battery power/horn driver 
error

strike hold on power may not function

513

TEST WIRE

no continuity on test wire for 
testing ESID

Information Center may not be able to 
reset ESID

515

STR VOLT

strike voltage input error

516

STR COIL

strike current input error

517

POST AC V

self test ac voltage input 
error

self test of ac voltage stake failed

518

POST AC I

self test ac current input 
error

self test of ac current coil failed

519

POST DC V

self test dc voltage input 
error

self test of dc voltage input amplifier 
failed

520

POST DC I

self test dc current input 
error

self test of dc current input amplifier 
failed

521

V NOT GND

strike voltage input stake not 
grounded

self test of voltage stake  failed

588

EEP WRITE

EEProm write error

ESID may not be able to record strike 
history

589

MISC CODE

invalid error report entry

software error report

Содержание JT5




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды