Ditch Witch JT5 Скачать руководство пользователя страница 14

Страница: 14 / 155

JT5 Operator’s Manual

Safety - 13

Emergency Procedures

CMW

Emergency Procedures

Before operating any equipment, review emergency procedures and check that all safety precautions have
been taken.

Electric Strike Description

When working near electric cables, remember the following:

•

Electricity follows all paths to ground, not just path of least resistance.

•

Pipes, hoses, and cables will conduct electricity back to all equipment.

•

Low voltage current can injure or kill. Many work-related electrocutions result from contact with less
than 440 volts.

Most electric strikes are not noticeable, but indications of a strike include:

•

power outage

•

smoke

•

explosion

•

popping noises

•

arcing electricity

If any of these occur, or if strike alarm sounds or flashes, assume an electric strike has occurred.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

274-050

EMERGENCY SHUTDOWN

- Turn ignition switch to stop position or push remote engine stop button (if

equipped).

Electric shock. Contacting electric lines will cause death

or serious injury. Know location of lines and stay away.

Содержание JT5




























































































































































Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch JT5, Руководство оператора

Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды