Ditch Witch JT5 Скачать руководство пользователя страница 102

Страница: 102 / 155

JT5 Operator’s Manual

Systems and Equipment - 101

DrillLok™/Tracker Control

CMW

DrillLok™/Tracker Control

Overview

This mode allows the tracker operator to disable hydraulic power to drilling unit thrust and rotation.

Operation with Ditch Witch

Tracking Equipment:

See tracker manual.

Operation without Ditch Witch

Tracking Equipment:

Only available on units with DrillLok™ system.

See DrillLok™ operation sheet.

Rotating shaft will cause death or serious injury. Stay

away.

To help avoid injury:

•

Use DrillLok/tracker control any time you change downhole tools or during other times when the drill
string is exposed.

•

If you are not using DrillLok/tracker control, turn off drilling unit before changing downhole tools.

NOTICE:

This mode does not disable thrust and rotation immediately. Functions are disabled within 16

seconds.

Troubleshooting Tip:

If thrust and rotation are

not enabled check whether the green
DrillLok™/tracker control light (shown), located
on drilling unit anchoring console, is on. If it is,
thrust and rotation have been disabled by
DrillLok/tracker control.

NOTICE:

Tracker operator cannot disable

thrust and rotation from tracker if DrillLok/
tracker control key is installed in drilling unit and
turned to the deactivated position.

See “DrillLok™/Tracker control key” on
page 22.

Содержание JT5




























































































































































Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch JT5, Руководство оператора

Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды