Dionex ICS-900 Скачать руководство пользователя страница 86

Страница: 86 / 142

ICS-900 Operator’s Manual

Doc. 065215-02 9/09

NOTE The

inlet

check valve assembly housing has a 1/4-28 port.

The

outlet

check valve assembly housing has a 10-32 port.

5. Inspect the new inlet check valve

assembly (P/N 045722) to verify that the
double-hole end of the cartridge is
visible (see

Figure 5-8

If the double-hole end is not visible,
remove the cartridge from the housing
and install it correctly.

Inspect the new outlet check valve
assembly (P/N 045721) to verify that the
single-hole end of the cartridge is visible.

If the single-hole end is not visible,
remove the cartridge from the housing
and install it correctly.

Figure 5-8. Check Valve Assemblies

Figure 5-7. Pump Heads

Secondary

Pump Head

Primary
Pump Head

Outlet Check
Valve

Inlet Check
Valve

Double-hole

Single-hole

Flow

Inlet Check Valve

Outlet Check Valve

1/4-28 Port

10-32 Port

Содержание ICS-900















































































































































Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды

Dionex ICS-900, Руководство оператора

Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды