Dionex ICS-900 Скачать руководство пользователя страница 62

Страница: 62 / 142

ICS-900 Operator’s Manual

Doc. 065215-02 9/09

To troubleshoot:

1. If a sequence is being executed, terminate the sequence by selecting

Stop

on the

Batch

menu.

2. Turn off the ICS-900 power briefly and then restart.

3. Try to toggle the valve from Load to Inject by clicking the

Inject

button

on the ICS-900 Control panel.

4. If the problem persists, contact Dionex for assistance.

Various electronics-related problems can cause this error message to be
displayed.

If this warning appears, contact Dionex for assistance. The ICS-900
electronics components cannot be serviced by the user.

This error indicates a problem in the pump controller electronics.

To troubleshoot:

•

Contact Dionex for assistance. The ICS-900 electronics components
cannot be serviced by the user.

This error indicates a problem in the pump controller electronics.

To troubleshoot:

•

Contact Dionex for assistance. The ICS-900 electronics components
cannot be serviced by the user.

Module data buffer overflow. Data may have been lost.

Pump motor lost control.

Pump pressure hardware error.

Содержание ICS-900















































































































































Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды

Dionex ICS-900, Руководство оператора

Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды