Dionex ICS-900 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 142

background image

1 • Introduction

Doc. 065215-02 9/09

3

1.3

Safety and Regulatory Information

The ICS-900 was manufactured by Dionex Corporation at the following location:
527 Lakeside Drive, Sunnyvale, CA 94088-3603 U.S.A. The ICS-900 is designed
for IC (ion chromatography) applications and should not be used for any other
purpose. Operation of an ICS-900 in a manner not specified by Dionex may result
in personal injury.

If there are questions regarding appropriate usage, contact Dionex Technical
Support. In the U.S., call 1-800-346-6390. Outside the U.S., call the nearest
Dionex office.

1.3.1

Safety Messages and Notes

This manual contains warnings and precautionary statements that can
prevent personal injury and/or damage to the ICS-900 when properly
followed. Safety messages appear in bold type and are accompanied by
icons, as shown below.

Appendix C
TTL and Relay
Control

Describes the ICS-900 TTL and relay control
features.

Appendix D
FAQ

Provides answers to frequently asked questions
about ICS-900 operation.

Appendix E
Introduction to Ion
Chromatography

Describes basic ion chromatography concepts.

Appendix F
Glossary

Provides definitions of terms commonly used in
ion chromatography.

Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.

«
...
9
10
11
12
13
...
»

Содержание ICS-900















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICS-900

Бренд: Qingdao H.Y Страницы: 6

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: Walker Bay Страницы: 8

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: Makita Страницы: 10

Бренд: DBX Bushido Страницы: 12

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренд: laerdal Страницы: 104

Бренд: laerdal Страницы: 33

Бренд: laguna Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды