Dionex ICS-900 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 142

background image

Doc. 065215-02 9/09

51

4 • Troubleshooting

This chapter is a guide to troubleshooting problems that may occur while
operating the ICS-900 Ion Chromatography System (ICS-900).

•

describes the error messages displayed in the Chromeleon or

Chromeleon Xpress Audit Trail.

•

through

describe other operating problems and how

to resolve them.

If you are unable to eliminate a problem, contact Dionex for help. In the U.S., call
Dionex Technical Support at 1-800-346-6390. Outside the U.S., call the nearest
Dionex office.

4.1

Alarms and Error Conditions

If any of the following alarm conditions occurs, an error message is displayed in
the Chromeleon or Chromeleon Xpress Audit Trail. Each error message is
preceded by an icon that identifies the seriousness of the underlying problem (see
the table below).

Icon

Severity Level

Description

Warning

A message is displayed in the Audit Trail, but the
current run is not interrupted.

Error

A message is displayed in the Audit Trail and the
system attempts to correct the problem (sometimes
by using an alternative parameter). An Error never
interrupts the current analysis; however, if it occurs
during the Ready Check, the analysis will not be
started.

Abort

A message is displayed in the Audit Trail and the
running batch is aborted.

«
...
57
58
59
60
61
...
»

Содержание ICS-900















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICS-900

Бренд: C.M.O Страницы: 10

Бренд: Jackco Страницы: 6

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: Yamaha Страницы: 46

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: Parkside Страницы: 2

Бренд: Park House Healthcare Страницы: 12

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: Gardena Страницы: 33

Бренд: A.HABERKORN Страницы: 28

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды