Digi MIL-3000FTX Series Скачать руководство пользователя страница 28

Страница: 28 / 163

MIL-3000FTX Series of FastPort Print Servers

3-3

6. Double-click on its displayed port (service) where the printer is

connected. A “

Select Driver

” dialog appears.

7. Choose a name for the printer.

8. Choose the driver for the printer that is connected to the FastPort port.

The “

Printer Setup

” dialog box displays.

9. Change any of the desired printer-specific settings.

10. Choose

Windows NT systems is now configured to print to FastPort.

3.1.4 Printing from Windows 95/98 or Windows NT 4.x (via SMB)

Note:

This installation requires FastPort firmware 6.1 or higher.

1. Open

Network Neighborhood

2. Choose the workgroup where FastPort is located.

3. Double-click on

FastPort

. FastPort appears as

FPXXXXXX

; where

XXXXXX is the last six digits of the MAC address.

Figure 3-1. FastPort Menu Select

4. Double-click the port where the print job will go.

5. The “Do you want to create a printer on your local machine that prints

to this device” dialog box appears. Click

Yes

on this dialog box.

6. When prompted, select the driver for the printer connected to the

specific printer port.

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды