Digi MIL-3000FTX Series Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 163

background image

MIL-3000FTX Series of FastPort Print Servers

F-3

Note:

Note the sequence number assigned to the images that is listed when using the DF
console command or enter the flash monitor. The higher number indicates the more
recent upload.

F.1.3 Flash Upload Commands

Access the flash upload command in one of two ways:

•

Make a serial port connection and run the serial monitor

•

For DOS machines, use the telnet monitor or use ACT

The flash upload commands are:

•

Disable Network Upload

Used for security against unauthorized uploads.

•

Enable Network Upload

This is the default state.

•

Restart in Other Bank

The only way to cause the older image to execute when the images
differ. The effect is temporary. A power cycle always runs the newer
image. Use this feature to compare the old version to the new version.

•

Copy This Image to Other Bank

Use this command to make the images identical. This command
updates the alternate bank with the new main bank when the user is
satisfied with the new image. To revert to an old firmware version, use
the

Restart in Other Bank

command. When the old version comes

up, this command will copy the old version over the new.

F.1.4 Troubleshooting Tips

•

The original three LEDs remain blinking. FastPort didn’t recognize the
beginning of the image. Check: baud rate. Verify: cable is correctly
connected. Verify: correct files are loading.

•

The rotating LED pattern begins and then freezes. This means that the
end of the download image is missing.

•

All LEDs flash

Warning:

If all LEDs flash after reprogramming has begun, then there was a hardware failure!

Note:

FastPort remains in these three error states until resetted by a power cycling.

«
...
140
141
142
143
144
...
»

Содержание MIL-3000FTX Series




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MIL-3000FTX Series

FrameSaver SLV 9126

Бренд: Paradyne Страницы: 24

Бренд: quadient Страницы: 130

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 629

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 61

Versant 80 Press

Бренд: Xerox Страницы: 26

Versant 80 Press

Бренд: Xerox Страницы: 230

Бренд: Xerox Страницы: 15

Бренд: Xerox Страницы: 9

DocuPrint 180 NPS Series

Бренд: Xerox Страницы: 172

Бренд: Xerox Страницы: 11

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 40

Color C75 Press

Бренд: Xerox Страницы: 340

DocuPrint N3225

Бренд: Xerox Страницы: 169

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды