Digi MIL-3000FTX Series Скачать руководство пользователя страница 96

Страница: 96 / 163

MIL-3000FTX Series of FastPort Print Servers

9-9

•

Show Node Name

: When this option is selected, the software displays

host names for all the devices discovered. Checked by default.

•

Show Node Address

: When this parameter is chosen, FastManage

displays IP and IPX addresses for all the devices discovered. Not
checked by default.

•

Load Saved Maps

: When this option is selected, FastManage loads a

saved Map when starting the Discovery Application. Checked by
default.

•

Save Maps On Exit

: When selected, this option saves the Map when

Discovery is exited. Checked by default.

•

Save Parameters On Exit

: This selection saves the options when

the Discovery is exit. Checked by default.

•

Refresh every

: When chosen, this option refreshes the Map every

<n>

seconds. Default is

seconds.

•

Discover

: When this parameter is selected, the software re-discovers

hosts every

<n>

seconds. Default is

90 secs

•

Dead

: This parameter signifies the number of attempts FastManage

tried before marking the node as “dead” (off-line). Default is

unicasts.

•

Wait

: The selection denotes the amount of time the software waits for a

reply from a node. Default is

second.

•

Default Map

: This parameter selects the name of the default Map file:

map.map

•

Map File

: This parameter enters the path for the Map file. Default is

C:/fm

•

Hosts File

: This parameter enters the path for the hosts file. Default

C:/ETC

•

Bootptab File

: This selection enters the path for the bootptab file.

Default is

C:/FM

•

Allow To Edit “Hosts” File

: When this parameter is selected, the

software updates the “hosts” file if a new host is discovered. Checked
by default.

•

Default

: Initialize all the parameters to default values.

•

Save Options

: Saves all changes to the

issnmp.ini

file.

•

Cancel

: Cancels the changes.

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды