Digi MIL-3000FTX Series Скачать руководство пользователя страница 125

Страница: 125 / 163

MIL-3000FTX Series of FastPort Print Servers

C-9

C.5.5 FastPort does not login to the file server

• Use the console

monitoring capability of ACT (in the

Monitor

menu)

to see the messages sent by FastPort.

• Use the

userlist

command (in NetWare 4.x, this is

nlist user

) to

see whether FastPort has logged in with the name: FPXXXXXX.

• In Bindery Emulation (Netware 2.x, 3.x) verify the following command

has been set in the file server:

SET ALLOW UNENCRYPTED PASSWORD=ON

• U use the

Monitor

menu in ACT. If a server is not listed, use the

Advanced Configuration

menu to force a configuration file server

to direct FastPort to search for a specific server.

• Force a frame type (refer to NetWare Configuration).

C.5.6 FastPort does not print via serial port

1. Verify that the serial port of the printer and FastPort match.

2. Check the serial cable.

3. Verify that FastPort is attached to the queue.

4. Check queue name

C.5.7 No Form Feed is sent after the print job

1. Verify the capture options using the command

capture

show

2. Check whether the form feed option has been disabled.

3. Run the

Print Manager

of MS Windows (3.x).

4. Check the

Windows Printer Setup

screen for a form feed check box.

C.5.8 PostScript jobs have trouble printing

Check the banner command settings. Use one of three methods:

• Use ACT to turn off the banner option for the queue.

• From DOS, use the

NPRINT

utility with the

/nobanner

option.

• From DOS, use NetWare’s capture with its

/nobanner

option.

• Verify printer supports postscript.

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды