Digi MIL-3000FTX Series Скачать руководство пользователя страница 98

Страница: 98 / 163

MIL-3000FTX Series of FastPort Print Servers

9-11

•

Times

: If this is enabled and a time is set, this option sets the number of

times FastManage “broadcasts” before giving up finding a node.
“Enable IP” must be selected to enable this option. Checked and

times are the default.

•

Poll “hosts” List

: If this is checked, FastManage reads through a

Map list, if a name is in the hosts file, it will then use SNMP to discover
a host. Checked by default.

•

Poll Map List

: If selected, this option “discovers” each host in a Map

through SNMP. Checked by default.

•

Find Only Digi Devices

: If checked, this option finds and displays

only Digi devices. Not checked by default.

•

Enable IPX

: If this option is selected, FastManage enables IPX

protocol. If not selected, FastManage will not perform any SNMP over
IPX operation. This protocol is checked if IP was selected during setup.

•

Do IPX Routing

: If this is enabled, user’s can manage IPX devices

across the router. If the device name is specified in the host file, then
that device will be discovered (the

Enable IPX

Do IPX routing

and the

Poll “hosts” list

all have to be enabled).

The “Enable IPX” parameter must be selected to enable this option.
Checked by default.

•

Do IPX Discovery

: Use SNMP over IPX and find all devices that

respond. The “Enable IPX” parameter must be selected to enable this
option. Not checked by default.

•

Enable NetBIOS

: When selected, this option enables NetBIOS using

the NetBEUI protocol. If not, FastManage will not perform any SNMP
over NetBIOS operation. This protocol is checked if IP was selected
during setup.

•

Strict Name Resolution

: If this is enabled, all device names

starting with SNMPA will be treated as NetBIOS names. The “Enable
NetBIOS” parameter must be selected to enable this option. Checked by
default.

•

Do NetBIOS Discovery

: If this parameter is chosen, the software

uses SNMP over NetBIOS to find all devices that respond. The “Enable
NetBIOS” parameter must be selected to enable this option. Not
checked by default.

•

Default

: Initialize all the parameters to default values.

•

Save Options

: Saves all changes to the

issnmp.ini

file.

•

Cancel

: Cancels the changes.

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды