Digi MIL-3000FTX Series Скачать руководство пользователя страница 50

Страница: 50 / 163

MIL-3000FTX Series of FastPort Print Servers

5-4

5.3.4 Installation on BSD UNIX Systems

Install.sh

creates a spool directory and makes a config. file

/usr/

spool/<

printer name>/.fpconfig

. To install:

1. Load the

install.sh

software.

2. Type

./install.sh

to run the install script.

3. Choose FastPort by its model number.

4. Choose

Option #1, LPD-based systems

5. If an IP address has not been assigned, select

Option #1, Configure

a FastPort

If one has been, go to step 7.

6. Choose the following:

a. Host naming method (

/etc/hosts/file

b. Host name and IP address for FastPort.

c. Hardware (Ethernet) address of FastPort.

d. UNIX system type.

e. Enter monitor mode and press [i] to assign an IP address.

f. Press [r] to issue a command to reset FastPort.

g. Continue to step 7 to install the printer.

7. At the main menu, select

Option #2, Install a printer or

plotter

. The software prompts for:

a. Whether to install host software or use direct LPD.

b. Type of data sent to the printer (

pcl, ps,

ascii

c. Where the printer port is connected to: serial or parallel.

d. Type of banner page.

Select

Option X

to Exit. BSD installation is complete.

5.4

Manual Installation on LPD Systems

Printing to LPD allows users to print as if they were directly attached to a
remote UNIX system. Configuration requires assigning an IP address and
setting up a remote BSD UNIX-like printer.

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды