Digi MIL-3000FTX Series Скачать руководство пользователя страница 152

Страница: 152 / 163

MIL-3000FTX Series of FastPort Print Servers

H-2

H.4 Discovery Application Messages

T a b l e H - 4 : Discovery Application Messages

H.5 Ping Application Message

T a b l e H - 5 : Ping Application Message

H.6 BOOTP Server Application Messages

Table H-6: BOOTP Server Application Messages

The address contains one field with value
more than 255. Not all fields are defined

A valid IP address is in the form of a.b.c.d, where a.b.c.d can
vary from 0 to 255. For example:

193.25.86.214

Host name appears as blanks

Create hosts file with a vertical list of host names:
“hostname space IP” or <host name> <IP address>

Message

Solution

IP, IPX, and NetBIOS Discovery are disabled. For
Discovery to work, at least one of them should be
enabled. Please update SNMP section, IP/IPX entries of
issnmp.ini file. Discovery will exit now

Valid Values are:
IP=YES or IP=NO
IPX=YES or IPX=NO,
NetBIOS=Yes or NetBIOS=No

Unable to open file (bitmap file)

The FastManage installation may be bad. Reinstall

Unable to copy palette for the bitmap

The FastManage installation may be bad. Reinstall

Unable to create bitmap from file DIB

The FastManage installation may be bad. Reinstall

No such pathway or drive is not ready

Restart Windows

Message

Solution

IP is disabled in the file issnmp.ini. IP needs to be enabled
for this application to run. This application will exit now

Enable IP discovery in the Discovery
Application to enabled IP

Problem

Cause

Solution

Please retry when there is a BOOTPtab
file

No Bootfile found

Enter BOOTPtab file and retry

IP is disabled in the file issnmp.ini. For
this application to run, enabled IP

IP discovery disabled in the Discovery
Application

Enable IP Discovery in the
Discovery Application to
enabled IP

Error to read packet

This message comes when a bad BOOTP
packet is received

Retry. If the problem still
persists, reset the device

The address should contain only HEX
digits. i.e., 0-9, and A-F/(a-f)

Validation for MAC address

Enter a valid MAC address

Hardware address is not specified. So
this entry cannot be saved

This message appears during the
operation “Add entry to BOOTPtab file”

Enter Host name address in the
user entry form

IP address is not specified. So this entry
cannot be save

This message appears during the
operation “Add entry to BOOTPtab file”

Enter IP Address in the user
entry form

This is not a valid hardware address

User input invalid MAC address

A valid hardware address is a
12 digit HEX number. For
example:

01.23.45.67.89.AB

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды