Digi MIL-3000FTX Series Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 163

background image

MIL-3000FTX Series of FastPort Print Servers

E-1

A p p e n d i x E

Troubleshooting AppleTalk

E.1 Troubleshooting Tips

The following are troubleshooting tips for AppleTalk.

E.1.1 Reset Time

The default for reset time may have to be changed. The reset time is the
amount of time FastPort waits before sending the next print job to a printer.
Since reset times for the printers vary greatly, FastPort uses values
specified by the variables

Wait Time Before Reset

and

Wait Time

After Reset

to delay sending print jobs before and after a reset sequence.

These are set via the

SetUp Defaults

file (see “Using Setup Defaults

File” on page 6-4).

E.1.2 Configuration to Use the ACK Signal

FastPort relies on the ACK signal from the printer. Sometimes printers
require the use of more signals (for example,

Busy

) to send correctly on the

interface. If the unit is having parallel flow control problems, modify the
flow control method (see “Using Setup Defaults File” on page 6-4).

E.1.3 Situation 1: Printing Over Ethertalk Using Driver 7.x

The serial port fails when the user tries to print over EtherTalk using driver
7.x to LaserWriter printers. For bi-directional printing support across the
serial interface (for LaserWriter II and II NT printers), use the following
procedure. The printer needs to be initialized with correct data and parity
values. Do this by either making a telnet connection into the serial port of
FastPort or connecting a terminal to the printer’s serial port.

1. Turn the LaserWriter off and set the front panel switches D1 and D2

down. This sets the Laser Writer in PS Batch Mode with these values for
RS-232 set for 9600 baud, RS-422 set for 9600 baud with port values of 7
data bits, no parity check, 1 stop bit, and Xon/Xoff.

2. Turn on the LaserWriter. It prints a test page with current settings.

«
...
130
131
132
133
134
...
»

Содержание MIL-3000FTX Series




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MIL-3000FTX Series

imageclass LBP251dw

Бренд: Canon Страницы: 72

ImageCLASS MF4270

Бренд: Canon Страницы: 248

imageclass LBP251dw

Бренд: Canon Страницы: 116

imageCLASS D1320

Бренд: Canon Страницы: 36

Serial Servers Vlinx VESR9xx

Бренд: B&B Electronics Страницы: 61

Бренд: DataCard Страницы: 2

Бренд: DataCard Страницы: 8

Бренд: DataCard Страницы: 8

Бренд: DataCard Страницы: 3

Бренд: Wang Страницы: 24

Бренд: Oki Страницы: 20

Бренд: NEC Страницы: 151

Бренд: HYVE Страницы: 22

Бренд: TYAN Страницы: 106

Бренд: Xerox Страницы: 2

SUPERSERVER 6035B-8R+

Бренд: Supero Страницы: 110

Бренд: Axiohm Страницы: 6

InterServe 600 Series

Бренд: Intergraph Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды