Digi MIL-3000FTX Series Скачать руководство пользователя страница 55

Страница: 55 / 163

MIL-3000FTX Series of FastPort Print Servers

5-9

The

fpfilter

software supports Adobe TranScript command line

arguments. To use these options, rename

fpfilter

as:

•

fpcomm:

Print to parallel port 1

•

fpcomm_s:

Print to serial port 1

•

fpcomm_p2:

Print to parallel port 2

•

fpcomm_s2:

Print to serial port 2

•

fpcomm_p3:

Print to parallel port 3

When no

-P

is given,

fpfilter

uses the directory for its name. If the

directory for alpha is

/usr/spool/fastport

, it tries FastPort as the host

name and prints with LPR or LP:

./fpfilter -P alpha -m -f /etc/hosts

5.5.2 Printer Options File (.fpconfig)

fpconfig

can be used instead of command line option.This simple text

file can be modified using an ASCII text editor.

fpfilter

checks the

directory specified by the

-D

command; if it is not present, it checks the

current directory for the

.fpconfig

file. If present, it changes the

fpfilter

behavior.

fpfilter

is executed by the spooling when using LPR.

fpfilter’s

directory is not that of the users.

fpfilter

is the spool directory. Syntax is

shown in Table 5-3. Entries appear and in any order.

-b

Send a banner file (BSD only)

-f

Send a final form feed

-m

Send CR/LFs for UNIX LFs

-D <dir name>

Look in the <dir. name> directory for the

.fpconfig

file

-A <a2ps filter>

Use the “a2ps” filter for ASCII to PostScript conversion

-d

Send a D at the beginning/end of a job (PS printers only)

-startfile <file>

Send file before print job

-endfile <file>

Send file after print job

-startstring “<str>”

Send “str” (string in quotes) before print job

-endstring “<str>”

Send “str” (string in quotes) after the print job

-syslog

Print the error messages into the “syslog” file

-mail <user>

Send E-mail to user at the end of print job if there is an error

-prog <prog-name>

Executes at the end of a job; sends the returned error code to it

-errorfile <file>

Use file to log errors

CLASS <hostname:port, List>

If the current printer is unavailable, tries printing to the device listed in the

List

(e.g., CLASS alpha:p1 CLASS alpha:p2)

-closewait

Closes all sent data before the socket closes

-pba

Adobe PostScript conversion for non-binary printers

-pbh

HP PostScript binary conversion for non-binary printers

Table 5-2: fpfilter Command Line Options

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды