Digi MIL-3000FTX Series Скачать руководство пользователя страница 26

Страница: 26 / 163

MIL-3000FTX Series of FastPort Print Servers

3-1

C h a p t e r 3

Installing and Printing in a MS Windows and IBM

OS/2 Environment

Chapter 3 provides detailed instructions on configuring and printing with
MS Windows and IBM OS/2 clients.

3.1

Printing From a NetBIOS Workstation

3.1.1 Introduction

FastPort supports native printing from Windows and IBM NetBIOS clients
using the NetBEUI protocol. To perform an installation on a NetBIOS
workstation:

1. Verify that

a. The network settings on the workstation include the NetBEUI

protocol.

b. The SMB or Windows Print and File client services are “bound” to

the NetBEUI protocol. This should have been done by default when
the protocol was first installed onto the system.

2. For Windows programs, refer to:

“Printing from Windows for Workgroups” on page 3-2

“Printing from Windows NT (3.5x)” on page 3-2

“Printing from Windows 95/98 or Windows NT 4.x (via SMB)” on page
3-3

This section describes how to install a logical Windows printer that will
send print jobs to FastPort.

3. For both DOS and Windows programs, refer to:

“Printing From NetBIOS-supported DOS Workstation” on page 3-4

This section describes how to use the

net use

command, which

redirects the LPT ports to FastPort.

Содержание MIL-3000FTX Series




































































































































































Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды

Digi MIL-3000FTX Series, Руководство пользователя

Результаты поиска

Содержание MIL-3000FTX Series

Отзывы:

Похожие инструкции для MIL-3000FTX Series

Бренды по названию

Популярные бренды