Digi MIL-3000FTX Series Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 163

background image

MIL-3000FTX Series of FastPort Print Servers

E-7

E.2.7 Downloading the Setup Defaults File to Change FastPort

The Setup Zone Name, Setup Printer Info, and Setup Font List files can also
be downloaded to change FastPort settings.

Note:

Apple products were designed to print to postscript printers. Any of the following
suggestions may or may not work on the workstation. There is no implied suggestion
that ASCII printing will work.

1. Insert the AppleTalk files from the CD-ROM.

2. Double-click on

Digi Technology AT Files

x.x

and on

Folder

.

3. Double-click on

3100

,

3100cx

,

3200

,

3400

,

3X00FTX

, or

3500

files

folder.

Using Apple to print ASCII from a print server:

a. Double-click on

SetUp Printer Info

file.

b. Change to

Postscript Printer

(no).

4. Double-click on

SetUp Defaults

file

5. Change the following in the parallel port 1 or 2 or serial port 1 or 2:

a. “Show in Chooser” (Yes)

b. “Before Reset Delay” (60)

c. “After Reset Delay” (60)

Note:

Steps b and c may slow down printing

6. Click on

File

and

Save As...

7. Choose the folder on the hard drive.

8. Save and close.

9. From the

Chooser

, click on

LaserWriter 8 (7)

.

10. Select the

FP, MILAN, or DIGI...-par1

.

11. Click on

Setup

,

OK

, and

Close

.

Note:

Ignore any messages about inability to print to a spooler.

12. Re-insert

Appletalk Utilities

files.

13. Double-click

Digi Technology AT Utilities

x.x

folder.

14. Double-click on

Utilities

folder.

«
...
136
137
138
139
140
...
»

Содержание MIL-3000FTX Series




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MIL-3000FTX Series

Бренд: TANDBERG Страницы: 187

Бренд: A10 Networks Страницы: 17

870 - SuperScript B/W Laser Printer

Бренд: NEC Страницы: 52

SuperScript 1800

Бренд: NEC Страницы: 8

Express5800/320Ma

Бренд: NEC Страницы: 80

Express5800/320Ma

Бренд: NEC Страницы: 90

ML-2240 - 23 Ppm Mono Laser Printer

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 8

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 134

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 112

Бренд: Samsung Страницы: 128

Бренд: Samsung Страницы: 152

ML 3471ND - B/W Laser Printer

Бренд: Samsung Страницы: 207

ML 2150 - B/W Laser Printer

Бренд: Samsung Страницы: 237

ML 3471ND - B/W Laser Printer

Бренд: Samsung Страницы: 103

ML 2150 - B/W Laser Printer

Бренд: Samsung Страницы: 217

ML-2010 - B/W Laser Printer

Бренд: Samsung Страницы: 122

Бренд: Samsung Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды