Curve Beam pedCAT Скачать руководство пользователя

Страница: 41 / 168

0473

90001

Rev

07.26.13

System Status Indicators

There are 4 indicator lights. These indicator lights are on the Operator’s control box and on the
machine itself on the upper right cover. There are also similar indicators within the Acquisition
software program.

The lights are as follows:



Power ON:

This is solid

Green

when the machine is ON.



Ready:

This is the Exposure Ready light and is

Green

when the machine is in

Ready state for exposing. This would indicate that it is time to press the exposure
button.



X-Ray ON:

This is an

Amber

color when the system is exposing, emitting X-ray.



Fault:

This would be

Red

in color if there was a failure in the system.

Status Indicator panel on Operator Control Box:

under Emergency Stop button.

Status Indicator panel on machine:

front right and left cover

Содержание pedCAT









































































































































































Результаты поиска

Содержание pedCAT

Отзывы:

Похожие инструкции для pedCAT

Бренды по названию

Популярные бренды

Curve Beam pedCAT, Руководство оператора

Результаты поиска

Содержание pedCAT

Отзывы:

Похожие инструкции для pedCAT

Бренды по названию

Популярные бренды