manualshive.com logo in svg

Curve Beam pedCAT, Руководство оператора

Поделиться
Скачать
Curve Beam pedCAT Скачать руководство пользователя страница 75

 

74

 

 

0473

  

 

    

90001

 

Rev

 

07.26.13

 

Perform the SECOND Scan

 (Large FOV) instructions by starting the Geometric 

Calibration again using the Large FOV Scan.   
 

Only perform the following steps after both Medium and Large FOV scans have 
been completed. 

 
Next the Geometry files that are used by the Recon Manager will need to be copied 
and then replaced with the newly created and edited file from above.  To do this, 
open the “Recon Manager Runtime” folder on the desktop.  From here, there are two 
folders that will be accessed.  The Configuration folder and the ConfigurationPass2 
folder.  In both of these two folders, locate the file “Geometry_768.xml” and rename it 
to “Geometry_768_YYYY_MM_DD.xml” where YYYY is the current year and 
MM_DD represents the current (today’s) month and date.  Then locate the file 
“Geometry_1368.xml” and rename it to “Geometry_1368_YYYY_MM_DD.xml” where 
YYYY is the current year and MM_DD represents the current (today’s) month and 
date.  This will need to be done TWICE, once for the Geometry_768.xml and 
Geometry_1368.xml files in the Configuration folder and once for the same files in 
the ConfigurationPass2 folder. 
 
Navigate back to the “GeoCal Files” folder that has the newly created and edited 
Geometry files.  Copy both the Geometry_768.xml and the Geometry_1368.xml files.   
Navigate on the desktop to the “Recon Manager Runtime” folder.  The copy of the 
geometry files will now need to be placed in BOTH the Configuration folder and the 
ConfigurationPass2 folder inside the “Recon Manager Runtime” folder.  So navigate 
to each folder and right click and select “Paste” to paste a copy of the geometry files 
in both the Configuration folder and the ConfigurationPass2 folder. 
 
Close the “Recon Manager Runtime” folder. 
 
Close the “GeoCal Files” folder. 
 
Start the Recon Manager Program. 
 
Close the Recon VM window. 
 
Place the Patient Platform in the scanner. 
 
All calibrations are complete. 
 
 
 

 

 

 

Содержание pedCAT









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды