manualshive.com logo in svg

Curve Beam pedCAT, Руководство оператора

Поделиться
Скачать
Curve Beam pedCAT Скачать руководство пользователя страница 120

 

119

 

 

0473

  

 

    

90001

 

Rev

 

07.26.13

 

To Reset the Slabs back to normal thin slices, click the “Reset Slab” button 

 on the Main 

Menu Bar. 
 
 

Image Enhancement Tools:

   These are functions that can be used to enhance and manipulate 

the image for optimal viewing. 

Window / Level (Brightness / Contrast):  

 

 

To adjust the Window/Level, select the Win/Lev icon and then selecting a window 
to make the window/level change to.  Changes are made by first clicking in the 
window, then moving the mouse up and down and then left and right until the 
optimal window/level is achieved.  To deselect the Window/Level function, click 
on the Win/Lev icon a second time. 

 

Zoom:  

 

 

If the image does not appear as close as desired, then select the Zoom icon and 
select a window to change the zoom factor on.  If you drag your mouse up, the 
image will zoom in and appear closer.  As the mouse is moved down, the image 
will appear further away.  To deselect the Zoom function, click on the Zoom icon 
a second time. 
 

Pan:  

 

To adjust the image to a different location inside the window, the Pan function 
can be utilized.  To center the section of the image desired in the window, select 
the Pan icon and then select the window to modify.  Click on the image and hold 
the mouse down, while moving the mouse around and the image will move with 
the mouse movements.  To deselect the Pan function, click on the Pan icon a 
second time. 

 

Image Magnifier:  

 

 

The Magnifier icon will provide a magnification of the selected image.  When the 
mouse is moved around the anatomy in the selected image box, the 
magnification box will be continually updated with the new location of the mouse.   

Содержание pedCAT









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды