manualshive.com logo in svg

Curve Beam pedCAT, Руководство оператора

Поделиться
Скачать
Curve Beam pedCAT Скачать руководство пользователя страница 6

 

5

 

 

0473

  

 

    

90001

 

Rev

 

07.26.13

 

Radiation Safety: 

X-rays are dangerous to both operator and others in the vicinity unless established safe 
exposure procedures are strictly observed.  Use the following safety measures to ensure safety 
to the Patient and Operator.  The useful and scattered beams can produce serious or fatal 
bodily injuries to Patients and persons in the surrounding area if used by an unskilled operator.  
Adequate precautions must always be taken to avoid or reduce exposure to the useful beam or 
to scattered radiation.  Operators are strongly urged to comply with the current 
recommendations of the International Commission on Radiological Protection and, in the United 
States, the US National Council for Radiological Protection.  

Use the following measures to protect yourself and the patient from unintended exposure to 
radiation.  Anyone who is near the patient during test procedures must observe the following 
precautions:  

  Maintain distance from exposed radiation source in accordance with the facility 

survey or site plan and shielding designs, provided by a medical physicist.  The 
plan/survey will be created based off of Scatter Measurements provided in this 
manual. 

  Keep exposure times to a minimum.  

  Patient must wear protective X-ray shielding items (lead apron, etc.) to protect 

anatomical areas.  We recommend all patients wear a protective shielding full wrap 
apron.  We recommend that patients less than 21 years old, small size patients 
(under 100 pounds) and children also wear a gonad and ovarian front and back 
protective shield.  Sample shielding products, or similar: 
Supplier: Marshield, Full Wrap Apron, #MS-SP1 
Supplier: Universal Medical Inc, Diaper 14" x 20", #800 

  Wear a PEN dosimeter and/or film badge.  

  If you are required in the exam room during a procedure, stay as far from the 

scanner as possible or behind a mobile protective wall. 

  The physician is responsible for protecting the patient from unnecessary radiation. 

 

System Safety Devices: 

Emergency Stop: 

 In the event of an emergency (any moving component collides with any 

parts of the equipment or items in the environment, or that could cause physical injury to the 
Patient), the Operator or Patient should utilize one of the 2 designated Emergency Stop buttons

 

to turn off the power to the X-ray and all moving parts in order for the Patient to be safely 
removed from the machine.  There is an Operator E-stop button on the Operator Control Box 
and there is a Patient E-Stop button on the machine by the seat.  The Emergency Stop (s) when 
activated will remove ALL power from the machine. If the machine gates are closed, they will 
have to be opened manually and any obstructions to the patient exit manually removed.   

 Warning System: 

The System is equipped with provisions for warning lights and/or audible 

alarms when X-ray power is energized.  An externally powered Warning System can be 

Содержание pedCAT









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды