Curve Beam pedCAT Скачать руководство пользователя | Manualshive

Страница: 158 / 168

background image

157

0473

90001

Rev

07.26.13

APPENDIX II: Troubleshooting

Error Messages:

System failures that may result in a scan failure will be accompanied by Error Messages in
the software. The user should follow the instructions to resolve the error, however if the
Warning message persists, the user should contact CurveBeam technical support at 267-
483-8081. If the system fails to operate in any other way or if your problem is not listed,
please contact CurveBeam technical support at 267-483-8081.

Firmware Monitoring Warning:

Upon startup of the “CB Scanning Device” Acquisition

software, the system checks that the embedded controller firmware software version is the
correct version to operate with unit. If an unsupported version number firmware software
resides on the embedded controller then the following error message will display and the
Acquisition software will terminate. In the event of this error message, please contact
CurveBeam technical support.

Temperature Monitoring Warnings:

The system is designed to send a Warning message

to the user if the internal temperature of the machine is below 35° C or above 45° C. This
Warning would display in the “CB Scanning Device” Acquisition software at Startup and just
before a scan is captured. If the temperature is below the 35° C limit then the resulting
image quality may not be optimal, however the system will permit scanning (for either upper
or lower temperature conditions).

The Warning message reads:

«
...
156
157
158
159
160
...
»

Содержание pedCAT









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для pedCAT

Бренд: Hanil Страницы: 60

Бренд: Baileigh Industrial Страницы: 40

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: Pari Страницы: 2

Бренд: Tascam Страницы: 78

MINISTUDIO CREATOR US-42

Бренд: Tascam Страницы: 11

Бренд: ubicquia Страницы: 36

Бренд: ABB Страницы: 33

Бренд: Tadano Страницы: 16

BRUTE AFS570010

Бренд: KStrong Страницы: 8

Бренд: Interacoustics Страницы: 2

Smartzone PViQ Connectivity System

Бренд: Panduit Страницы: 179

Бренд: ALLEN & HEATH Страницы: 6

Impression FR10 Bar

Бренд: GLP Страницы: 65

Бренд: Waters Страницы: 236

Бренд: NightBalance Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды