Curve Beam pedCAT Скачать руководство пользователя страница 18

Страница: 18 / 168

0473

90001

Rev

07.26.13

Environmental Specifications:

Operating:



The operational temperature range shall be 59°F to 86°F (+15°C to +30°C).



The operational humidity range shall be 25 to 60% relative humidity, non-

condensing.



The minimum time period that the room environmental operating conditions must be

maintained prior to powering the system is 1 hour.

Transportation and Storage:



The storage and transport temperature range shall be -4°F to 122°F (-20°C to

+50°C).



The storage & transport humidity range shall be 10% to 95% relative humidity, non-

condensing.

Scanner and Acquisition Computer (server):



Requires a Dedicated Line and a Surge Protector is recommended.

Patient Platform:



Maximum patient weight capacity: 400 lbs. (181kg)

Patient Seat:



Maximum patient weight capacity: 300 lbs. (136kg)

Handle Bars:



Maximum weight capacity: 150 lbs. (68kg)

Disposal:

Follow local regulations on disposal of waste parts. The

X-ray source assembly, image

sensor

and

all electronic circuits

should be regarded as non environmental friendly

waste product

The system does not generate, or require the use of, any materials that

require special disposal instructions as part of regular operation.

Extension Cords:

Do not use any extension cords which are not provided with the system. Be aware that
multiple portable socket outlets or extension cords are not to be connected to the
system.

External Items:

Do not connect any items or equipment to this system which are not part of the system.

Содержание pedCAT









































































































































































Результаты поиска

Содержание pedCAT

Отзывы:

Бренды по названию

Популярные бренды

Curve Beam pedCAT, Руководство оператора

Результаты поиска

Содержание pedCAT

Отзывы:

Бренды по названию

Популярные бренды