Curve Beam pedCAT Скачать руководство пользователя | Manualshive

Страница: 123 / 168

background image

122

0473

90001

Rev

07.26.13

will remove ALL patient information from the image other than Patient ID#. This

can be useful if the desire is to maintain a level of anonymity when viewing the scan on
the screen. The image should NOT be printed when the Privacy icon is selected and no
patient data is displayed. To allow for the basic patient information, then the Text

Overlay icon should be selected.

This allows the user to display some

information but also remove the excess information from the Image Windows.

Projection Mode:

There are 2 options available for projection mode, one is “Radiographic”, the second is
“MIP”. Radiographic is the image displayed as a normal radiograph.
MIP stands for Maximum Intensity Projection. This is an image tool that is only usefull
for thick slice slabs. It will display for each pixel, the most dense valued pixel in the
depth of the selected slab, which means it will display the brightest pixel (voxel). Below
is a comparison of a thick slice slab as a Radiographic projection vs. an MIP projection.

Radiograph

MIP

To alternate between Radiograph and MIP, click the Proj. Mode icon. It will display to

you which mode it is currently toggled to.

Filters:

There are 3 filter options available; Smooth, Normal, Sharp. Filters can be applied to
enhance images. The default filter type will be Normal. But if the image requires a little
more detail, than the Sharp filter can be selected. Smooth will make the edges of the
images appear more smooth, but may lose some detail. Filters are often a personal
preference. Select the Filters icon to apply one of the 3 options.

Measurements:

There are various measuring tools for treatment planning.

HU: These are for measuring Hounsfield Units, which is density value of an area of
interest.
Angle: These are for measuring angles on the anatomy of interest.

«
...
121
122
123
124
125
...
»

Содержание pedCAT









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для pedCAT

Бренд: ABB Страницы: 86

Бренд: ABB Страницы: 14

Бренд: Cambro Страницы: 6

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Garmin Страницы: 20

Бренд: h/p/cosmos Страницы: 81

Бренд: laerdal Страницы: 9

Бренд: Rain Harvesting Страницы: 2

Бренд: Sable Страницы: 28

McDonnell & Miller PSE-800-M

Бренд: Xylem Страницы: 20

Бренд: B medical systems Страницы: 28

WaterLink Spin Touch DW

Бренд: LaMotte Страницы: 64

High End Systems SolaPix 7

Бренд: ETC Страницы: 36

DL30x30-G525/24V

Бренд: Vision & Control Страницы: 32

Бренд: Ultra Products Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды